Contact Us

HMC849ALP4CETR

Brand: Analog Devices
Analog Devices HMC849ALP4CETR is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC849ALP4CETR — Analog & Mixed-Signal ICs | Superb Automation

HMC849ALP4CETR

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC849ALP4CETR from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC849ALP4CETR: a DC to 6 GHz SPDT switch with 60 dB of isolation

The HMC849ALP4CETR is a non reflective GaAs pHEMT single pole double throw switch that works from DC to 6 GHz in a 16-lead 4 mm by 4 mm QFN. It takes a single positive control of 0 and 3 V or 0 and 5 V, holds up to 60 dB of isolation, and presents 0.8 dB of insertion loss with an input third order intercept of +52 dBm. The non reflective property and the all off state are what make it useful at the front end of a radio that has to survive a transmit burst on one port while receiving on the other.

Published values

ParameterValue
ConfigurationSPDT, non reflective, GaAs pHEMT
Frequency rangeDC to 6 GHz
IsolationUp to 60 dB, 53 dB minimum from 4 to 6 GHz
Insertion loss0.8 dB typical, 1.5 dB maximum at 4 to 6 GHz
Input IP3+52 dBm
P1dB compression+31 dBm
ControlSingle positive, 0/+3 V or 0/+5 V
All off stateEnable input held high
Return loss, on state17 dB
Package16-lead QFN, 4 mm x 4 mm

Isolation at the band edge is the number that decides the board arrangement

The 60 dB figure is quoted at the low end of the band. From 4 GHz to 6 GHz the guaranteed minimum falls to 53 dB, and that is the number to use for a 5 GHz front end, not the headline. On a transmit and receive switch, 7 dB less isolation means seven times more transmit energy reaching the receive chain, which on a sensitive low noise amplifier is the difference between a protected input and a damaged one.

The all off state adds a third position that a plain SPDT does not have. Holding the enable pin high puts both ports in isolation, which is used during calibration or when the antenna is disconnected, and it also means the control logic has to drive two lines, not one.

Power handling and the intercept point

A +31 dBm compression point and a +52 dBm intercept point put this switch in the class of parts that can sit after a driver amplifier rather than only at the antenna. The limit is reached at the band edges, where the loss is higher and the compression point falls, so the budget is checked at 6 GHz rather than at 1 GHz.

Control interface and what to verify

Two control voltages are accepted, and the current drawn is very low, so the switch can be driven from a microcontroller pin with a level shifter. Before a substitute is accepted the control truth table has to be compared line by line, because a part with inverted logic will look identical on a bench test with one control line held fixed and fail when the firmware toggles it.

The pages that answer this most often are defense grade components for the family alternatives, component lead time solutions for the acceptance test, and how to verify a drop in replacement for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Does the switch need a negative supply? No, it takes a single positive control voltage of 0 to 3 V or 0 to 5 V. Negative control is a feature of other switch families and is not required here.

Is it safe to leave both RF ports open? The switch is non reflective, so an open port does not reflect the signal back. Terminating the unused port is still good practice on a board where the switch sits between a filter and an amplifier.