Contact Us

HMC8205BCHIPS

Brand: Analog Devices
Analog Devices HMC8205BCHIPS is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC8205BCHIPS — Analog & Mixed-Signal ICs | Superb Automation

HMC8205BCHIPS

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC8205BCHIPS from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC8205B chips: 45.5 dBm at 50 V, and where 52 W of heat goes

The HMC8205B in chip form is a gallium nitride power amplifier for 0.4 GHz to 4 GHz that delivers 45.5 dBm (35.5 W) with 24 dBm in and 22 dB of power gain, at 40 percent power added efficiency with 28 dBm in, from a 50 V supply at 1300 mA quiescent. The die is 4.8 mm by 3.4 mm by 0.1 mm. It is the highest power part in this catalogue, and the arithmetic that matters is not the 45.5 dBm but the 88 W of DC input behind it.

Published values

ParameterValue
Frequency range0.4 GHz to 4 GHz, specified as two slices
Output power with 24 dBm in45.5 dBm typical
Power gain22 dB typical with 24 dBm in
Power added efficiency40 percent typical with 28 dBm in
Supply50 V at 1300 mA quiescent
Die size4.8 mm by 3.4 mm by 0.1 mm
DC input at rated outputabout 88 W, which is 1.76 A at 50 V
Dissipation at rated outputabout 52 W
Band split0.4 GHz to 0.8 GHz and 0.8 GHz to 4 GHz tables
Typical usehigh power transmitters, electronic warfare, test systems

Eighty eight watts in for thirty five and a half out

At 45.5 dBm the output is 35.5 W and 28 dBm in is 0.63 W, so 34.9 W is added. At 40 percent that is 88 W of DC input, which at 50 V is 1.76 A. The 1300 mA quiescent figure on the front page is the no drive current, and the operating current is a third higher again.

The heat side is 52 W at rated output. That is not a number a small carrier absorbs; it needs a copper tungsten or copper diamond carrier, a serious heat sink and a thermal interface that is specified rather than assumed. In pulsed service the average scales with duty cycle, which is how most systems use a part like this, but the pulse itself still puts 52 W through the attach for its duration.

Forty percent efficiency at 4 GHz is the rated point

Efficiency falls as frequency rises for a given process, and this part is rated over a decade of bandwidth. The 40 percent figure belongs to the higher drive condition, and lower drive gives lower efficiency because the quiescent current is still flowing. A system that runs at 10 dB of backoff should expect efficiency in the mid teens rather than 40 percent, and the thermal budget has to be built on the backoff figure.

This is the general trap with high power gallium nitride: the data sheet efficiency belongs to saturation, and a linear application such as a multi carrier transmitter runs well below it. The DC input does not fall much with drive, so the heat at backoff is close to the heat at saturation, and the heat sink is sized by the worst case rather than by the rated efficiency.

Two band slices for one decade

The part is specified from 0.4 GHz to 0.8 GHz and from 0.8 GHz to 4 GHz in separate tables, and the gain and power figures differ between them. An application at 3 GHz should be quoted from the second table, where the bandwidth is nine hundred percent and the matching has to cover it.

A decade of bandwidth from a single die means the output match is a compromise. That is acceptable in a transmitter that drives a fixed antenna through a filter, and it is a problem in a system that drives a load which changes with frequency, such as a broadband antenna or a test fixture. In those cases the load pull at the band edges is the thing to measure, not the data sheet typical.

The pages that answer this most often are the RF power transistor cross reference for the family alternatives, defense grade components for the acceptance test, and how to choose an RF amplifier for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Is 45.5 dBm a continuous rating? The published condition is a drive of 24 dBm in for 45.5 dBm out, and the dissipation at that point is about 52 W. Continuous operation at that level needs a thermal solution built for 52 W, and most systems run the part pulsed.

What 50 V supply current should be budgeted? About 1.76 A at rated output, against a 1300 mA quiescent figure. The supply, the wiring and the reservoir all have to carry the operating current, not the quiescent one.