Contact Us

HMC733LC4B

Brand: Analog Devices
Analog Devices HMC733LC4B is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC733LC4B — Analog & Mixed-Signal ICs | Superb Automation

HMC733LC4B

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC733LC4B from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC733LC4B: 10 to 20 GHz, and a 22 V Tune Range That Sets the Loop Supply

The HMC733LC4B is a wideband monolithic voltage controlled oscillator with an internal buffer, covering 10 GHz to 20 GHz from a single +5 V supply at 70 mA. It delivers about +3 dBm, holds a single sideband phase noise of -90 dBc/Hz at 100 kHz offset and -60 dBc/Hz at 10 kHz, and tunes with an analog voltage from 0 V to +22 V. That tuning ceiling is the item that propagates furthest into the system, because it decides the supply of the charge pump and the topology of the loop filter, not just the oscillator.

A 22 V tuning port and a 5 V charge pump do not meet

Most integrated phase locked loops run their charge pump from 3.3 V or 5 V. To drive a port that needs 22 V, there are three routes. An active loop filter with a gain stage powered from a higher rail, a charge pump with its own 24 V or 28 V supply, or a step up converter dedicated to the loop. Whichever is chosen, the loop filter amplifier has to be fast enough not to add its own pole inside the loop bandwidth, and the higher rail has to be clean, because noise on the tuning line is multiplied by the tuning sensitivity in exactly the same way as noise on the supply.

The published figures

ParameterValueWhat it decides
Frequency range10 GHz to 20 GHzCovers X and Ku band with a single component
Output power+3 dBm typicalNeeds a following amplifier to reach a mixer drive level
Phase noise at 10 kHz-60 dBc/HzDominates the close in performance of the link
Phase noise at 100 kHz-90 dBc/HzWell inside the loop bandwidth of a typical narrow loop
Tuning voltage0 V to +22 VDetermines the loop supply and the filter topology
Supply current70 mA at +5 V350 mW, plus the loop and the buffer that follows

Tuning sensitivity is not constant, and the loop has to survive both ends

A wideband oscillator with a single varactor has a sensitivity that climbs as the tuning voltage rises, sometimes by a factor of three across the range. The loop bandwidth is proportional to that sensitivity, so a filter calculated at the middle of the range can be narrow and quiet at one end and wide and marginal at the other. The practical method is to simulate the loop at three tuning voltages, low, middle and high, and to check the phase margin at each. Where the variation is too large, a two band arrangement with a switchable capacitor is the usual fix, and it has to be planned before the board is committed.

Buffered output, still not a driver

The internal buffer isolates the oscillator core from the load and makes the output far less sensitive to what follows than an unbuffered oscillator would be, but +3 dBm is 2 mW. A passive mixer that wants +17 dBm of local oscillator drive needs 14 dB of gain and a filter after this part, and that amplifier has to be linear enough not to convert the oscillator's own harmonics back down into the band. The second harmonic of the oscillator sits at 20 GHz to 40 GHz, which is usually outside the filter's passband and inside the amplifier's bandwidth, so the amplifier's output filter is doing double duty.

Where such an oscillator is used, and how it is replaced

The band and the phase noise put this part in radar, electronic warfare and test equipment rather than in consumer radio. Availability for those programmes is a long term question, and the replacement route usually keeps the same tuning voltage range so that the loop filter does not have to be recalculated. The RF component sourcing page lists the oscillator family, the defense grade components page covers the screening options, and current allocation and lead time are on the component lead time solutions page.