Contact Us

HMC641ALP4E

Brand: Analog Devices
Analog Devices HMC641ALP4E is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC641ALP4E — Analog & Mixed-Signal ICs | Superb Automation

HMC641ALP4E

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC641ALP4E from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC641A: A Four Throw Switch That Arrives as Bare Die and Needs a Negative Rail

The HMC641A is a nonreflective single pole four throw switch covering 0.1 GHz to 18 GHz, with 2.1 dB of insertion loss and 42 dB of isolation to 12 GHz. It carries an on chip binary two to four line decoder, so four throws are selected with two control lines instead of four. The two facts that shape every board it goes on are less obvious: it is supplied as a bare gallium arsenide chip measuring 1.92 mm by 1.60 mm by 0.102 mm, and it runs from a negative supply of -5 V to -3 V with negative logic control.

Bare die is an assembly decision, not a package choice

There is no lead frame and no solder joint. The die has to be attached to a carrier and connected with ribbon bonds, and the published electrical data was taken with every RF pad bonded by a single 3.0 mil by 0.5 mil ribbon of minimal length. That bond is part of the RF circuit: a longer ribbon adds inductance, which shows up as extra loss at the top of the band and as a change in the return loss at the bottom. The part therefore belongs in a module or a chip on board assembly with a bonder and a wire pull test, not on a surface mount line. A team without that process should be looking at a packaged four throw switch even if it costs more per unit.

The numbers that travel with the die

ParameterValueNote
Frequency range0.1 GHz to 18 GHzNonreflective, so unused ports stay terminated
Insertion loss2.1 dB typical to 12 GHzDegrades towards the band edge
Isolation42 dB typical to 12 GHzBetween the selected port and the others
Power handling24 dBm through the path, 23 dBm into a terminated portMeasured at -5 V on the negative rail
Compression and intercept+25 dBm and +41 dBmBoth quoted at -5 V, both fall at -3 V
ControlTwo lines, two to four decoder, negative logicLevel shifting needed from 3.3 V logic

The decoder saves control lines, not a supply

A two to four decoder inside the switch is often read as a way to simplify the control interface. It does simplify the count, from four lines to two, but both of those lines still swing between zero and a negative voltage, and the supply is still negative. A microcontroller pin cannot drive either. The usual arrangement is a level translator per line, powered from the same negative rail the switch uses, so that the logic threshold tracks the RF supply over temperature.

-3 V is the minimum, not an alternative

The switch is specified over a negative supply of -5 V to -3 V, and the compression and intercept figures in the table are quoted at -5 V. Running at -3 V to save a converter is allowed by the absolute maximum ratings but costs linearity, and in a multi throw switch the loss of linearity appears first on the selected path at high input power. Where the negative rail is generated by a charge pump, the ripple on that rail also modulates the switch, so the pump should be followed by a linear post regulator or by a well damped filter.

Replacement and sourcing

Because the part is die, a replacement has to match the pad geometry before anything else, and pad geometry is rarely published for parts from other vendors. In practice the board is reworked rather than the part substituted, which makes availability the deciding factor. The RF component sourcing page lists the switch family, the obsolete RF part replacement page covers the end of life route, and die lots are inspected against the incoming inspection plan.