Contact Us

HMC465LP5

Brand: Analog Devices
Analog Devices HMC465LP5 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC465LP5 — Analog & Mixed-Signal ICs | Superb Automation

HMC465LP5

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC465LP5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC465LP5: a 5 mm package for a part that swings 10 V peak to peak

The HMC465LP5 is the surface mount order code of the DC to 20 GHz distributed driver amplifier, in a 32 lead 5 mm by 5 mm package with 25 square millimetres of board. The electrical behaviour is the same as the die: 15 dB of gain, 3 dB of noise figure, 25.5 dBm saturated, 10 V peak to peak of swing to 12 GHz and 160 mA from 8 V. What the package changes is the impedance at the ports at the top of the band, the thermal path under 0.93 W of dissipation and the fact that no wire bonding is needed.

Published values

ParameterValue
Package32 lead, 5 mm by 5 mm, 25 square millimetres
Frequency rangeDC to 20 GHz
Gain16 dB typical DC to 6 GHz, 15 dB 6 to 12 GHz, 12.5 dB 12 to 20 GHz
Saturated output power25.5 dBm, 25 dBm and 23 dBm across the three bands
Saturated output voltage10 V peak to peak to 12 GHz, 8 V peak to peak above
Output power at 1 dB compression24 dBm, 23 dBm and 20 dBm
Output third order intercept32 dBm, 28 dBm and 24 dBm
Noise figure3.0 dB to 12 GHz, 4.0 dB above
Return loss20 dB in and 22 dB out in the low band, 8 dB in and 12 dB out in the top band
Supply8 V at 160 mA
Thermal resistancequoted for the die, add the attach and paddle path for the package
Assemblyreflow onto a land pattern with an exposed paddle

Where the package costs voltage swing

A distributed amplifier reaches its output through an artificial transmission line, and the last element of that line is the bond pad. In a package the pad is followed by a lead frame and a solder joint before the board, each of which adds series inductance and shunt capacitance. At 10 GHz the effect is small enough that the 10 V peak to peak figure still holds in most assemblies. At 18 GHz the same transition is a larger fraction of a wavelength, and the swing available into a reactive load falls before the 23 dBm power figure does.

The practical consequence is that a packaged driver should be characterised into the load it will actually see. A 50 ohm measurement with a power meter gives the table in the document; a modulator gate, a transformer or a diode pair gives something else, and the difference at the top of the band can be several volts of swing. Buying the die and bonding it into the final cavity removes one transition, and on this part that is a real engineering reason rather than a cost exercise.

Point nine three watts through a 25 square millimetre paddle

At 8 V and 160 mA the part draws 1.28 W and dissipates 0.93 W at the saturated point. That is not a difficult number for a 5 mm package with an exposed paddle, provided the paddle is soldered to a via field and the far side of the board has copper. What makes it easier than the power amplifier codes in the same family is that the dissipation is nearly constant, so the thermal steady state can be calculated once and trusted.

Where it becomes difficult is in a stack. A driver is often the last stage before an optical modulator or an antenna, sitting next to a power amplifier that does dissipate a lot, and the local ambient is then set by the neighbour. The 0.93 W figure assumes the paddle is at the board temperature, so the question to ask of a board is not how hot this part gets but what the board under it is at, and that number comes from the neighbours.

Three anchors for an incoming test

Gain at 1 GHz of about 16 dB, at 10 GHz of 15 dB and at 18 GHz of 12.5 dB are enough to catch a swapped or damaged part, and the return loss at 10 GHz of 15 dB input and 17 dB output catches a lifted paddle or a bad solder joint at the ports, which shows up as a reflection long before it shows up as a gain error.

The bias check is the drain current at 8 V with VGG1 at the value written on the traveller. A part that needs more than about minus 1.4 V to reach 160 mA is at the edge of the range, and one that reaches 160 mA with VGG1 near zero has a damaged gate. Recording the gate voltage per serial number is cheap and it is the only way to tell a lot trend from a failure later.

When an order code in this family cannot be found, the RF component sourcing page lists what else does the same job, RF procurement covers what to check before a part is dropped into an existing board, and how to verify a drop in replacement is the route we take on a live shortage.

Two questions buyers ask

Can the package be substituted for the die without requalification? No. The port transitions and the thermal path both change, so gain at the top of the band and the swing into a reactive load have to be measured again.

Is 25.5 dBm the right number for a driver budget? It is the saturated 50 ohm figure. For a modulator or a high impedance load the 10 V peak to peak row is the one that describes the part.