Contact Us

HMC464LP5

Brand: Analog Devices
Analog Devices HMC464LP5 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC464LP5 — Analog & Mixed-Signal ICs | Superb Automation

HMC464LP5

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC464LP5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC464LP5: a 5 mm lead frame package carrying 1.9 W of heat

The HMC464LP5 is the surface mount order code of the 2 GHz to 20 GHz distributed power amplifier, supplied in a 32 lead lead frame chip scale package with a 5 mm by 5 mm body and a 0.85 mm height, which is 25 square millimetres of board. The amplifier delivers 14 dB of gain in the low band, 26.5 dBm at one decibel compression and 27.5 dBm saturated from 8 V at 290 mA. The package is the difference from the die order code in every respect that matters to a build: the heat leaves through the exposed paddle, the ports leave through lead frame transitions, and the assembly is reflow rather than attach and bond.

Published values

ParameterValue
Package32 lead LFCSP, 5 mm by 5 mm body, 0.85 mm height, 25 square millimetres
Frequency range2 GHz to 20 GHz, three specified bands
Gain14 dB typical 2 to 6 GHz, 13.5 dB 6 to 16 GHz, 11 dB 16 to 20 GHz
Output power at 1 dB compression26.5 dBm, 25 dBm and 21 dBm across the three bands
Saturated output power27.5 dBm, 26 dBm and 24 dBm
Output third order intercept32 dBm, 26 dBm and 22 dBm
Noise figure4.0 dB typical to 16 GHz, 6.0 dB from 16 GHz to 20 GHz
Supply8 V at 290 mA, 2.32 W of DC
Gate biasVGG2 at 3 V typical, VGG1 adjusted for 290 mA
Thermal resistance19.4 degrees per watt, channel to ground paddle
Continuous dissipation3.35 W at 85 degrees, derate 51.5 mW per degree above
Channel temperature150 degrees maximum
RF input power20 dBm absolute maximum at 8 V

The exposed paddle is the whole thermal answer

At 290 mA and 8 V the part draws 2.32 W and delivers 447 mW at the compression point, so 1.87 W has to cross the paddle. The vendor thermal figure of 19.4 degrees per watt is quoted to the paddle, not to the air, which means the number is only valid if the board under the paddle is a real heat spreader. A via field of 0.3 mm holes at 0.6 mm pitch under a 3 mm by 3 mm paddle is about twenty five vias, and that is the minimum that turns the paddle into a plane rather than into a set of isolated pads.

Copper thickness matters more here than in a receiver. One ounce copper spreading 1.9 W over 25 square millimetres reaches a different steady state from two ounce copper over the same area, and the difference shows up as 10 to 15 degrees of paddle temperature. Since the derating curve starts at 85 degrees, that difference is the difference between 3.35 W of allowed dissipation and about 2.6 W, and at 2.32 W of DC the second case leaves very little room for a mismatch.

Power supply sequencing on a packaged part with one enable

The package brings all of the bias pins out on the same side of the body, which makes a tidy drawing and a dangerous power up order. VGG1 must be at its negative end before VDD arrives, and VGG2 must reach 3 V before VGG1 is walked up. A single enable pin that gates all three rails together does not do that, whatever the symbol on the drawing suggests, because the rails do not rise at the same rate.

A three rail sequencer with a current measurement on the drain is the reliable route, and it costs one small part. The cheaper alternative is a resistor from VGG1 to the negative rail that holds the gate off until the drain is up, plus a divider on VGG2 that tracks VDD, and that works as long as the negative rail is the first to arrive and the last to leave. Both approaches are testable, and the test is the same: scope the drain current during power up and confirm it stays under a few milliamps until VGG2 is present.

Screening a 5 mm package at goods inwards

The part is a two port amplifier with a specified return loss in each band, so a vector measurement at 2 GHz, 10 GHz and 18 GHz is enough to catch a wrong or damaged device without a full sweep. Gain at 2 GHz of about 14 dB, at 10 GHz about 13.5 dB and at 18 GHz about 11 dB are the three anchors, and a part that reads 14 dB at all three has probably been measured with a fixture that is not de embedded.

The bias point is the second check and the more useful one. Setting VGG1 for 290 mA at 8 V and recording the gate voltage gives a spread that tracks wafer lot, and a part that needs more than about minus 1.4 V to reach 290 mA is close to the edge of the adjustment range. Recording that number per serial number turns a later field return into a data question rather than an argument.

The pages that answer this most often are the RF power transistor cross reference for the family alternatives, RF procurement for the acceptance test, and vendor consolidation for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Is the LP5 footprint the same as the die? No. One is reflowed onto a land pattern with an exposed paddle, the other is attached and wire bonded, and the thermal and radio frequency paths are completely different.

What board copper does 1.9 W need? Enough to keep the paddle under 85 degrees: a via field under the paddle and a ground plane on the far side at minimum, with two ounce copper preferred, because the derating curve starts at 85 degrees.