HMC463LP5
Product Specifications
HMC463LP5
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC463LP5 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC463LP5: the same 2 GHz to 20 GHz amplifier with a package in the way
The HMC463LP5 is the surface mount order code of the 2 GHz to 20 GHz pHEMT distributed amplifier, and the electrical table on the vendor document belongs to the chip, taken in a fixture with 0.025 mm bonds of 0.31 mm. Buying the packaged code does not change the amplifier, it changes the transition at each port, the thermal path from channel to board and the handling that the assembly line has to be able to do. For a buyer comparing LP5 against die, the useful question is where the extra loss appears and what it costs to keep the rest of the table.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 2 GHz to 20 GHz, same amplifier as the die order code |
| Gain | 15 dB typical 2 to 6 GHz, 14 dB typical 6 to 20 GHz |
| Noise figure | 2.5 dB typical from 6 to 18 GHz, 3.0 dB typical 2 to 6 GHz |
| Gain control | VGG2 second gate, about 10 dB of range |
| Output power at 1 dB compression | 19 dBm typical 2 to 6 GHz, 16 dBm 6 to 18 GHz |
| Saturated output power | 20 dBm to 21 dBm |
| Output third order intercept | 26 dBm to 31 dBm across the band |
| Supply | 5 V at 60 mA, 80 mA maximum |
| Gate bias | VGG1 minus 0.9 V typical, adjustable minus 1.5 V to minus 0.5 V |
| Die size, reference | 3.05 mm by 1.29 mm by 0.1 mm |
| Thermal resistance | 48.6 degrees per watt, channel to die bottom |
| Assembly | reflow, no wire bonding on site |
| Reference measurement | 0.025 mm wire bonds of 0.31 mm on a 50 ohm fixture |
What the package adds at the top of the band
A package puts a transition, a lead frame and a longer bond loop between the die pad and the board. At 2 GHz those are a few tenths of a decibel and the 1.0 dB flatness allowance of the low band absorbs them. At 20 GHz a loop of 0.6 mm instead of 0.31 mm is enough to move the input match, and the symptom is a gain slope that tilts down at the top of the range rather than a part that fails a limit.
The output third order intercept of 26 dBm at the top band is the number that degrades first in a packaged assembly, because the intercept is set by the voltage swing at the output device and any extra series inductance at the port reduces the swing available before compression. A receiver that needs the 31 dBm figure belongs in the low band; one that works at 18 GHz should budget on 26 dBm whatever the order code.
Sixty milliamps is low enough that the package is a thermal question, not a current one
0.3 W of DC with 0.22 W dissipated is small for a 5 mm body, and the 48.6 degrees per watt figure is the channel to die bottom path, not the whole path once a package sits in it. What has to be added for a packaged part is the attach, the lead frame and the solder joint, so the same 0.22 W produces a larger rise than the die figure alone suggests. On a board at 85 degrees the difference is a few degrees and not a risk; it becomes a risk when the part is driven into compression for long periods, where the dissipation is set by the DC point and not by the radio frequency output.
The second thermal consideration is the neighbouring part. A distributed amplifier die is 3.05 mm by 1.29 mm inside a package that is 5 mm on a side, so a large part of the footprint is lead frame and mould compound that conduct heat poorly. Placing a power amplifier next to it on the same board raises the local ambient without changing the dissipation of this part at all.
Why a programme still buys the package first
The package removes die attach, wire bonding and the visual inspection that goes with them from the flow. For a build of tens of boards a month that is the difference between a process nobody owns and a reflow profile the contract assembler already runs. Die becomes attractive when the volume justifies the assembly step, or when the loss at 20 GHz has to come back out of the budget.
The procurement side is easy to miss. Die and package are separate order codes with separate lead times, separate moisture sensitivity handling and separate end of life behaviour, because a Hittite era amplifier of this family is only available from the remaining stock of each code. That stock does not run out at the same time, so a build that has qualified on the package should know whether the die is still buyable before it treats the two as interchangeable.
Two pages worth reading before a purchase order goes out are the RF component sourcing page and obsolete RF part replacement; the first lists what else fits the socket, the second is the test sequence for a drop in, and component lead time solutions covers the case where the shortage is already on the line.
Two questions buyers ask
Can the LP5 be used without a negative rail? No. VGG1 still needs about minus 0.9 V relative to the source to set 60 mA, and the package does not include a bias generator.
Does the packaged part keep the 0.15 dB flatness? The flatness figure comes from the chip measurement. Expect the packaged part to be close in the mid band and less flat at the top of the range, so verify gain at 18 GHz to 20 GHz on the first article.