HMC463LH250
Product Specifications
HMC463LH250
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC463LH250 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC463LH250: the hermetic order code and the questions it raises
The HMC463LH250 is the hermetic surface mount order code of the same 2 GHz to 20 GHz pHEMT distributed amplifier that is sold as HMC463 die and HMC463LP5 in a plastic package. The amplifier is unchanged: 14 dB of gain, 2.5 dB of noise figure at 10 GHz, 19 dBm at one decibel compression and 60 mA from 5 V, with a second gate for about 10 dB of gain control. What changes with a hermetic body is the qualification route, the moisture handling and the price, and those are the three things that decide whether a programme needs this code at all.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 2 GHz to 20 GHz |
| Gain | 14 dB typical, 12 dB minimum |
| Noise figure | 2.5 dB typical at 10 GHz, 3.0 dB typical at 2 GHz to 6 GHz |
| Output power at 1 dB compression | 19 dBm typical 2 GHz to 6 GHz, 16 dBm 6 GHz to 18 GHz, 14 dBm 18 GHz to 20 GHz |
| Output third order intercept | 31 dBm, 28 dBm and 26 dBm across the same three bands |
| Supply | 5 V at 60 mA typical, 80 mA maximum |
| Gate bias | VGG1 minus 0.9 V typical, minus 1.5 V to minus 0.5 V range |
| Gain control | VGG2, about 10 dB |
| Die size, reference | 3.05 mm by 1.29 mm by 0.1 mm |
| Thermal resistance | 48.6 degrees per watt, channel to die bottom |
| Operating temperature | minus 55 to plus 85 degrees |
| Storage temperature | minus 65 to plus 150 degrees |
When the hermetic body is worth the price and when it is not
A hermetic package is bought for two reasons: a specification that demands it, and an environment where moisture ingress through a mould compound would end the life of the part. The electrical table does not improve, so a programme that buys LH250 and expects better noise figure or more output power is buying the wrong thing. What it gets is a sealed cavity and a body that can be screened to a military flow, including temperature cycling and gross and fine leak, which a plastic part cannot offer whatever the datasheet numbers say.
The other side of that trade is availability. These are Hittite era order codes now sold from remaining inventory, and the hermetic code is the one that usually runs out first because it was bought in smaller quantities to begin with. A programme that cannot substitute the plastic package for schedule reasons should hold a buffer of the hermetic code rather than assume a second buy will be possible.
Screening, and what to ask for on the purchase order
The vendor document for this family states an operating range of minus 55 to plus 85 degrees, a storage range of minus 65 to plus 150 degrees and an ESD class, and that is all. It does not contain a screening table. A buyer who needs a military flow has to put the screening on the purchase order as a separate requirement, with the test methods named, because the standard order code does not carry it. That is the single most common misunderstanding on a part like this and it surfaces at goods inwards, not at quotation.
The same applies to radiation. Nothing in the document addresses total dose or single event effects, and the applications list mentions military and space as suitable uses of the amplifier rather than as qualified environments. For a space programme the die is the more usual starting point, because the assembly and the screening are then under the customer's own control, and this order code becomes a benchmark rather than a flight part.
Sixty milliamps means the hermetic body is not the thermal limit
0.3 W of DC and 0.22 W of dissipation at the compression point is small enough that the body is not what limits the part. The 48.6 degrees per watt channel to die bottom figure belongs to the die, and the package adds its own interfaces on top, so the practical rise depends on how the body is attached to the board and how much copper sits under it, not on the cavity.
What does change with a sealed body is repair. A hermetic part that has been soldered down and then found to be out of specification at test cannot be reworked the way a plastic package can, and the reflow profile has to be developed on scrap hardware rather than on the first build. That is a schedule cost rather than a technical one, and it belongs in the quotation stage.
Where a customer needs a second position on this part, defense grade components is the starting point, RF procurement sets out the checks a substitution has to pass, and the obsolete part cross reference hub is the short lead time route we quote against.
Two questions buyers ask
Is the HMC463LH250 a drop in for the LP5 footprint? Not necessarily. The two are different bodies with different outlines, so the land pattern has to come from each order code's own package drawing.
Does the hermetic code include military screening? No. Screening has to be specified on the order, because the vendor document lists only the operating and storage ranges and the ESD class.