Contact Us

HMC424ALP3ETR

Brand: Analog Devices
Analog Devices HMC424ALP3ETR is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC424ALP3ETR — Analog & Mixed-Signal ICs | Superb Automation

HMC424ALP3ETR

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC424ALP3ETR from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC424A: Six Bits, 0.5 dB Steps and Control Lines That Want Minus 5 V

The HMC424A is a six bit gallium arsenide digital attenuator covering dc to 13 GHz, with 0.5 dB steps to a total of 31.5 dB, a typical step error of 0.5 dB, and a single negative bias of -5 V that allows operation down to dc. Six control inputs select the state, and those inputs swing between 0 V and -5 V. That is the opposite polarity from the positive control parts in the same family, and it is the first thing to check when a board is being ported from one to the other.

Insertion loss and the DC capability come together

ParameterValueConsequence
Frequency rangedc to 13 GHzUsable at an intermediate frequency, not only at RF
Attenuation range31.5 dB in 0.5 dB stepsSix bits, 64 states
Insertion loss dc to 4 GHz2.8 dB typical, 3.3 dB maximumThe lowest loss in the family at the bottom of the band
Insertion loss 8 to 13 GHz3.9 dB typical, 4.4 dB maximumRoughly 1 dB more than at the low end
ControlSix lines, 0 V and -5 VNeeds a level translator per line from 3.3 V logic
Switching30 ns rise and fall, 50 ns on and offFast enough for a slot level gain change

Two intercept figures, and the conservative one is on the front page

The first page quotes an input third order intercept of +38 dBm, while the specification table lists +45 dBm in the reference state and +42 dBm in the attenuation states. The front page figure is the lower one, so a link budget that uses it will be conservative, but a reader who takes the table figures will overestimate the headroom by 4 to 7 dB. Where the attenuator sits directly after a driver stage, the reference state is not the worst case anyway, because the worst case is a high attenuation state with a strong signal present, which is +42 dBm.

Negative control is not just a wiring detail

Six lines that idle at -5 V need a translator that can source and sink into a negative rail, and the translator's own supply has to come up in the right order relative to the -5 V rail. A common failure at bring up is a translator that powers from 3.3 V and drives the control pins before the negative rail exists, which forward biases the control junction through the part's internal diodes. The symptom is a channel that works after a power cycle and not on a cold start, and the fix is a sequencing note on the drawing, not a new part.

Why dc matters more than the band edge

Operation down to dc means this attenuator can be used in a baseband or intermediate frequency chain, where a positive control part with off chip ac coupling cannot go. It also means there is no series capacitor to block a dc offset, so the attenuator becomes part of the dc path of whatever it sits in, and the bias of the following stage has to be considered. That is the hidden cost of the dc capability, and it is usually discovered on the first board rather than in the part selection.

Sourcing and substitution

The replacement question here is polarity first, step size second, band third. A positive control part with the same footprint will attenuate correctly and will be driven by the wrong logic states, which reads as a part that measures a fixed pad. The RF component sourcing page lists the attenuator family, the obsolete RF part replacement page covers end of life, and attenuation is verified on receipt under the incoming inspection plan.