HMC1086-Die
Product Specifications
HMC1086-Die
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The HMC1086-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
HMC1086-Die: 25 W from 2 GHz to 6 GHz, and the quiescent current that is half the real one
The HMC1086-Die is a gallium nitride monolithic power amplifier covering 2 GHz to 6 GHz with 44.5 dBm of saturated output, 23 dB of small signal gain and 46 dBm of output third order intercept from a 28 V supply at 1100 mA quiescent. The vendor document describes the F10 flange mounted body of the same amplifier, and the die carries the same electrical table with a different thermal path.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 2 GHz to 6 GHz |
| Saturated output power | 44.5 dBm, about 28 W |
| Compressed output power, 4 dB | 41 dBm |
| Power gain at saturation | 11 dB |
| Small signal gain | 23 dB from 2 to 4 GHz, 24 dB from 4 to 6 GHz |
| Output third order intercept | 46 dBm at 33 dBm per tone |
| Power added efficiency | 35% from 2 to 4 GHz, 32% from 4 to 6 GHz |
| Supply | 28 V at 1100 mA quiescent |
| Gate bias | VGG between -8 V and 0 V to set 1100 mA |
| Input and output match | 50 ohm, dc blocked |
| Package of the published document | 10-lead flange mount |
1100 mA cannot be the driven current
28 V at 1100 mA is 30.8 W. At 35 percent efficiency, 44.5 dBm, or 28.2 W, of output requires 80.5 W of dc input, which at 28 V is 2.88 A. The 1100 mA in the table is therefore the quiescent current with no drive, and the supply, the feedthrough and the bulk capacitance all have to be sized for roughly 2.9 A.
If a board is built for 1.1 A the rail will sag on every pulse and the output will droop with it, and the fault will look like a gain problem rather than a supply problem. The measured dc input current under drive is the number to put in the power budget, and it is not on the front page.
Efficiency falls at the top of the band
35 percent from 2 GHz to 4 GHz against 32 percent from 4 GHz to 6 GHz is a small change in the table and a large change in the heat. At 32 percent the dc input for the same output is 88 W rather than 80.5 W, so 7.5 W more has to be removed from the same package.
For a continuous wave application the top of the band is therefore the thermal worst case, and it is the point at which the junction temperature should be calculated. For a pulsed radar the duty cycle scales everything, and the average dissipation is what the carrier has to pass.
Die against flange body
The published document is the F10 flange mount, which is a sealed ceramic package with a metal flange, dc blocked ports and a thermal path through the flange. The die version removes the package and the flange, so the heat goes into the carrier the module builder provides, and the radio frequency launch is the module's rather than the package's.
That is a gain in performance and a loss in convenience. Above 4 GHz the package parasitics are significant, so a module using the die can hold a wider bandwidth than the packaged part. Below 4 GHz the packaged part is usually the better engineering choice because the assembly is repeatable and the thermal path is specified.
Biasing a depletion mode gallium nitride part
The gate range that sets 1100 mA is -8 V to 0 V, which is a wide window and tells you the threshold varies part to part. The gate must be applied before the drain and removed after it, so the bias circuit is a sequencer with a clamp rather than two regulators and a switch.
A gate supply that fails to negative while the drain is up will destroy the amplifier in milliseconds, and a drain that is switched without the gate clamped will do the same. Both failure modes are avoided with a few components and a documented sequence, and both are common in first articles.
Buyers usually arrive at the amplifier cross reference to find the family alternatives, then use defense grade components to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.
Two questions buyers ask
What current does the HMC1086-Die draw under drive? At 44.5 dBm and 35 percent efficiency the dc input is about 80.5 W, which at 28 V is 2.88 A. The 1100 mA in the specification is the quiescent current without drive.
Are the ports dc blocked? The published F10 body has internally dc blocked ports. On the die the blocking is external, so the module has to provide it in the bias network.