Contact Us

HMC-AUH249-Die

Brand: Analog Devices
Analog Devices HMC-AUH249-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC-AUH249-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC-AUH249-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC-AUH249-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC-AUH249-Die: 15 dB and 23 dBm to 35 GHz, a driver with output power as well as swing

The HMC-AUH249-Die is a gallium arsenide HEMT distributed driver amplifier chip covering DC to 35 GHz with 15 dB of gain and 23 dBm of saturated output, and it is the member of the driver pair that states an output power as well as an output voltage. It delivers more than 8 V peak to peak and draws 200 mA from 5 V, in a die just under 4 square millimetres.

Published values

ParameterValue
Frequency rangeDC to 35 GHz, 37 GHz typical 3 dB bandwidth
Small signal gain15 dB typical
Output power at 1 dB compression21 dBm from DC to 5 GHz
Saturated output power23 dBm from DC to 5 GHz
Output voltagegreater than 8 V peak to peak
Supply5 V at 200 mA
Bias controlsVGG1 sets bias current, VGG2 sets output gain
Gain variation1 dB typical
Group delay variation10 ps typical
Die size2.2 mm x 1.80 mm x 0.1 mm

A driver that also has a compression point

Most modulator drivers publish a voltage swing and no compression point, because the load is capacitive and the concept does not apply cleanly. This one publishes 21 dBm at 1 dB compression and 23 dBm saturated from DC to 5 GHz, which is the band where a 50 ohm termination is the realistic load. Above 5 GHz the published table stops quoting power and the swing is the specification.

That split tells a user where the part is a power amplifier and where it is a voltage driver. A system that needs 100 mW of radio frequency below 5 GHz can use it as an amplifier, and a system that needs an 8 V swing at 30 GHz is using it as a driver, and the two are not the same operating point.

Five volts at 200 mA for one watt

1 W of dc input for 23 dBm, or 200 mW, of output is 20 percent at saturation in the low band, which is respectable for a class A distributed stage. At 35 GHz the output power is not specified and the voltage swing is, so the efficiency in that band is a function of the load rather than of the bias.

The die is 2.2 mm by 1.80 mm, so the 1 W is spread over 4 square millimetres. That is 0.25 W per square millimetre, which an epoxy attach to a grounded carrier will handle, unlike the power amplifiers in the same range that need a metal carrier.

Group delay and gain variation

10 ps of group delay variation and 1 dB of gain variation across the band are the numbers that matter for a modulated signal, and they are published because the intended application is a transmitter. A driver with a flat amplitude response and a varying delay distorts a wideband signal in a way that an amplitude measurement does not reveal.

For a module the interconnect will add to both. The published figures are for the die in a probed environment, so a module measurement of 15 ps is not necessarily a problem with the die.

Die against module

The die needs a bias tee, dc blocking and bypass capacitors on both bias lines, plus the ribbon bonds and the carrier. The vendor states this explicitly, and a first article that omits the bias tee will show a low frequency gain that looks like a die problem.

The 37 GHz typical bandwidth against a 35 GHz specification is the usual margin between a guaranteed and a typical figure. A board that needs 37 GHz has to be measured, because the specification stops at 35.

Two pages worth reading before a purchase order goes out are the amplifier cross reference and defense grade components; the first lists what else fits the socket, the second is the test sequence for a drop in, and component lead time solutions covers the case where the shortage is already on the line.

Two questions buyers ask

Is the HMC-AUH249-Die a power amplifier or a driver? Both, in different bands. It publishes 23 dBm saturated from DC to 5 GHz and a greater than 8 V peak to peak swing across the band, so below 5 GHz it can be used as a small power stage and above it as a modulator driver.

What external components does it need? A bias tee on the output, dc blocking, and bypass capacitors on the bias lines, with VGG1 setting the bias current and VGG2 the gain.