Contact Us

HMC-ALH508-Die

Brand: Analog Devices
Analog Devices HMC-ALH508-Die is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

HMC-ALH508-Die — Analog & Mixed-Signal ICs | Superb Automation

HMC-ALH508-Die

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The HMC-ALH508-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

HMC-ALH508 die: 4.5 dB of noise figure across 71 GHz to 86 GHz

The HMC-ALH508 is a three stage gallium arsenide HEMT low noise amplifier die covering 71 GHz to 86 GHz with 13 dB of small signal gain, 4.5 dB of noise figure, 7 dBm at one decibel compression, 8 dB of input return loss and 10 dB of output return loss, from three drains at 2.1 V, 2.1 V and 2.4 V drawing 30 mA in total. The die is 3.2 mm by 1.6 mm by 0.1 mm. At 30 mA of total current this is a receive part rather than a driver, and every figure in the table is a probed die measurement at 25 degrees.

Published values

ParameterValue
Frequency range71 GHz to 86 GHz
Gain11 dB minimum, 13 dB typical
Noise figure4.5 dB typical
Input return loss8 dB typical
Output return loss10 dB typical
Output power at 1 dB compression7 dBm typical
Supplydrains at 2.1 V, 2.1 V and 2.4 V, 30 mA total
Gate biasVGG1 and VGG2 minus 1 V to plus 0.3 V, minus 0.5 V typical
Die size3.2 mm by 1.6 mm by 0.1 mm
Measurement basisprobed die at 25 degrees

Three drains and two supply voltages on one die

The third stage runs at 2.4 V and the first two at 2.1 V, which is not an accident of geometry: a distributed low noise amplifier distributes the gain along a line, and the output stage is biased slightly harder to hold the compression point while the first stages are biased for noise. A bias board that feeds all three from one 2.1 V node will work and will give up part of the 7 dBm compression point; one that feeds all three from one 2.4 V node will raise the current in the first two stages and move their noise figure.

Thirty milliamps in total across three drains is about 10 mA per stage, which is a deliberate choice for a receive chain. The dissipation is roughly 65 mW, small enough that the die runs cool, and the reason the current is kept low is that the noise contribution of a HEMT rises with drain current well before the gain stops improving. A user who raises the current to gain compression point will lose the 4.5 dB noise figure that the part is bought for.

Four and a half decibels at 86 GHz is a link budget decision

At 80 GHz a receiver front end is usually built from a mixer with a conversion loss of 8 to 10 dB and an intermediate frequency amplifier, or from this amplifier followed by a mixer. Putting 13 dB of gain and 4.5 dB of noise figure ahead of the mixer takes the cascaded noise figure from about 9 dB to about 5 dB, which is a 4 dB improvement in sensitivity, worth more than any plausible improvement in antenna gain on a small terminal.

The catch is that 13 dB of gain is not much, so the noise figure of the mixer still matters. The Friis arithmetic with 13 dB of gain and a 9 dB mixer gives 4.5 plus 0.5, which is 5 dB; with a 15 dB mixer it is 5.2 dB. The first stage dominates, which is the point of the part, and it also means that any loss between the antenna and the die, including a waveguide transition, a filter or a radome, adds directly to the system figure.

An 8 dB input match and the assembly that follows

Eight decibels of input return loss is a voltage standing wave ratio of about 2.3 to 1, which is acceptable for a first stage whose input comes from an antenna through a transition. What it does mean is that the input bond wire is part of the matching network, and a ribbon of a different length moves the match. At 86 GHz the wavelength on a 0.1 mm alumina substrate is about 2 mm, so a 0.2 mm ribbon is a tenth of a wavelength and cannot be treated as a short circuit.

For a module the input transition is usually a waveguide to microstrip launcher followed by a short bond into this die. The launcher is specified by its own vendor and the bond by the assembly drawing, and what has to be measured is the pair together, because a launcher that is well matched into 50 ohm on its own can be several decibels worse when the bond adds its inductance in front of an amplifier with an 8 dB match.

Sourcing notes for this family: the RF component sourcing page holds the cross references, the LNA selection guide is the pre substitution check, and how to choose an RF amplifier is what we use when the part on the drawing is not on the shelf.

Two questions buyers ask

Can all three drains run from one supply? They can, and the third stage is specified at 2.4 V against 2.1 V for the first two. Running all three at 2.1 V costs some compression point, and running all three at 2.4 V raises the current and moves the noise figure.

Is 4.5 dB the noise figure over the whole 71 to 86 GHz band? It is the typical figure for the band. The document gives one value rather than a curve, so a wideband receiver should confirm the figure at the band edges on the first article.