ADPA7006-Die
Product Specifications
ADPA7006-Die
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADPA7006-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADPA7006 die: 23.5 dB of gain and 29.5 dBm from 18 GHz to 28 GHz
The ADPA7006 in die form is a gallium arsenide pHEMT amplifier covering 18 GHz to 28 GHz with 29.5 dBm of saturated output power, 29 dBm at one decibel compression, 23.5 dB of gain and 38 dBm of output third order intercept, from 5 V at 800 mA. The die measures 2.750 mm by 1.805 mm by 0.102 mm and is matched to 50 ohm on chip. Among the mid band parts in this family it has the most gain per stage, which is what makes a two stage chain reach 46 dB of gain without a third device.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 18 GHz to 28 GHz, specified as two slices |
| Output power at one decibel compression | 29 dBm |
| Saturated output power | 29.5 dBm |
| Gain | 23.5 dB |
| Output third order intercept | 38 dBm |
| Supply | 5 V at 800 mA |
| Die size | 2.750 mm by 1.805 mm by 0.102 mm |
| Matching | 50 ohm input and output |
| Integrated detector | on chip power detector |
| Gate bias | adjusted to reach 800 mA quiescent |
Four watts in, 0.89 W out, 3.1 W into the attach
800 mA at 5 V is 4.0 W of DC input. Saturated output is 0.89 W, so 3.1 W is dissipated in a die face of 4.96 square millimetres, which is 0.63 W per square millimetre. That is the densest of the mid band parts, and it is why the die is normally mounted on a carrier with a thermal expansion match rather than directly on laminate.
The 102 micrometre thickness keeps the thermal path short through the substrate but makes the die fragile in handling, which is an assembly cost rather than an electrical one. An assembly house that is set up for 100 micrometre gallium arsenide will not notice it; one that handles 250 micrometre silicon will break a percentage of the die at pick and place.
Twenty-three and a half decibels changes the chain count
Two of these give 47 dB of small signal gain with 29.5 dBm of saturated output. A chain that would have taken three 15 dB stages takes two, and the parts count, the bias channels and the 3.1 W heat sources all drop by a third. The catch is that the second stage is driven hard enough that its own compression shapes the chain response.
At 29 dBm output the second stage needs about 5.5 dBm of input, which the first stage delivers with 24 dB of headroom left. The chain therefore compresses at the output stage first, which is the arrangement you want: the level at which the chain stops being linear is set by one device rather than by the interaction of two.
Detector accuracy across a ten gigahertz span
The on chip detector is temperature compensated and tracks the envelope, and in die form its output is a pad. Across 18 GHz to 28 GHz the detector slope varies with frequency, so a level loop that calibrates at 23 GHz and then tunes to 28 GHz will read a different power than it is delivering. The correction table has to be built per band slice, not per part.
For a buyer the practical question is whether the detector is used as a power measurement or as a health indication. As a health indication, slope variation across the band does not matter. As a measurement, it needs a calibration table and a stable temperature, and at that point an external coupler and detector is often the cheaper route.
Two pages worth reading before a purchase order goes out are the RF component sourcing page and obsolete RF part replacement; the first lists what else fits the socket, the second is the test sequence for a drop in, and one stop RF supply covers the case where the shortage is already on the line.
Two questions buyers ask
Is 29.5 dBm specified over the whole 18 GHz to 28 GHz range? The 29.5 dBm and 23.5 dB figures belong to the 20 GHz to 28 GHz slice. The 18 GHz to 20 GHz slice is specified separately in the same data sheet.
What is the advantage of the die over the packaged part? Lower loss at the band edges and a smaller footprint. The packaged part adds a tested interface and a quoted thermal resistance but loses about a decibel at 28 GHz.