ADPA7001-Die
Product Specifications
ADPA7001-Die
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADPA7001-Die from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADPA7001-Die: 50 GHz to 95 GHz from a 3.5 V supply, and the bond wire that decides the top octave
The ADPA7001-Die is a gallium arsenide pHEMT balanced medium power amplifier die covering 50 GHz to 95 GHz, with 14.5 dB of gain and 17 dBm at 1 dB compression in the lower half of the band and an on chip temperature compensated power detector. It runs from 3.5 V at 350 mA and is matched to 50 ohm at both ports, which is what allows it to be dropped into a multi chip module without a matching network of its own.
Published values
| Parameter | Value |
|---|---|
| Frequency range | 50 GHz to 95 GHz |
| Gain, 50 to 70 GHz | 14.5 dB typical |
| Gain, 70 to 90 GHz | 14 dB typical |
| Output power at 1 dB compression, 50 to 70 GHz | 17 dBm typical |
| Output power at 1 dB compression, 70 to 90 GHz | 17.5 dBm typical |
| Saturated output power | 21 dBm typical |
| Output third order intercept, 50 to 70 GHz | 25.5 dBm typical |
| Output third order intercept, 70 to 90 GHz | 25 dBm typical |
| Input return loss, 50 to 70 GHz | 22 dB typical |
| Output return loss, 50 to 70 GHz | 19 dB typical |
| Supply | 3.5 V at 350 mA |
| Power detector | on chip, temperature compensated |
| Die size | 2.5 mm x 3.32 mm x 0.05 mm |
The band splits into three and the numbers follow
The datasheet is written in three ranges, 50 to 70 GHz, 70 to 90 GHz and 90 to 95 GHz, and the gain, compression point and intercept are stated per range. That structure is a warning: the headline 14.5 dB belongs to the lower range, and a link budget that assumes it at 94 GHz is betting on a number the vendor has not published.
At the top of the band the part is still useful, and the reason is the balance between gain and match rather than raw output. A receiver front end at 90 GHz needs enough gain to set the noise figure of the following stage, and 14 dB does that while keeping the input match good enough that the preceding filter does not see a reactive load.
Why the bond wire sets the usable top frequency
The die is connected with a 0.076 mm ribbon bond of minimal length, and the datasheet says so explicitly because the measurement depends on it. A 0.3 mm ribbon is roughly 0.3 nH, which is about 180 ohm of reactance at 95 GHz, and that reactance sits in series with a 50 ohm port. Any assembly that lengthens the bond, or uses a wire instead of a ribbon, moves the top of the band down and adds a mismatch the die cannot correct.
The practical result is that two multi chip modules built to the same drawing can measure differently at 90 GHz purely because of the bond loop height. A programme that needs the top octave should specify the ribbon geometry in the assembly drawing, not just the part number.
Power, efficiency and the detector
3.5 V at 350 mA is 1.225 W of dc input. At saturation the output is 21 dBm, or 126 mW, so the conversion is about 10 percent, and at 1 dB compression it is about 4 percent. This is a linear driver, not a power stage, and the dissipation is dominated by the bias current rather than by the radio frequency output.
The on chip detector gives a dc voltage proportional to output power with its own reference pin, which removes a coupler and a diode from the module. It is temperature compensated, so it can be used for level control rather than only for fault detection, but it is a detector on the output of the amplifier, so it cannot distinguish a load mismatch from a real power increase.
Applications and the assembly route
Test instrumentation, military and space equipment and telecommunications infrastructure are the listed uses, and all three share the same requirement: a repeatable gain block above 50 GHz with a known compression point. Instrumentation additionally benefits from the detector, because a leveled source needs one.
Because the die is 2.5 mm by 3.32 mm and 50 micrometres thick, it is handled as a chip rather than as a packaged part, with eutectic or epoxy attach and ribbon bonds. A buyer ordering this part is ordering a die in a gel pack or on a wafer frame, and the assembly house has to be equipped for millimetre wave bonding before the part is useful.
Two pages worth reading before a purchase order goes out are the amplifier cross reference and defense grade components; the first lists what else fits the socket, the second is the test sequence for a drop in, and vendor consolidation covers the case where the shortage is already on the line.
Two questions buyers ask
Is the ADPA7001-Die available in a packaged form? The part documented here is the die, matched to 50 ohm and intended for multi chip modules. A programme that needs a packaged connectorised part has to look at a different product, since a package adds its own transition above 50 GHz.
What does the detector output track? Output power, temperature compensated, against its own reference pin. It is on the amplifier output, so it reports delivered power and not incident power, and a mismatch changes the reading.