ADP3186JRUZ
Product Specifications
ADP3186JRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADP3186JRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADP3186JRUZ: a multiphase controller for a processor core rail that no longer gets new boards
The ADP3186JRUZ is a 5-bit programmable, 2, 3 or 4 phase synchronous buck controller in a 28-lead TSSOP. It reads a voltage identification code from the processor, sets the output between 0.8 V and 1.55 V, and drives logic level PWM outputs at up to 1 MHz per phase. It belongs to the generation of processor core supplies built around AMD VRM modules, which is why most enquiries about it now come from repair, legacy industrial boards and last time buys rather than from new programmes.
Published values
| Parameter | Value |
|---|---|
| Phases | 2, 3 or 4, selectable |
| Switching frequency | Up to 1 MHz per phase, set by the RT resistor |
| Output voltage | 0.8 V to 1.55 V, 5-bit VID programmable |
| Sensing accuracy | 1% worst case differential sensing over temperature |
| Current balancing | Active balancing between all output phases |
| Protection | Programmable short circuit limit with latch off delay, crowbar blanking |
| Supply and temperature | Specified over 0 C to 85 C commercial range |
| Package | 28-lead TSSOP, also offered in QSOP |
| PWM outputs | Logic level, for external drivers |
Why the VID code is the whole function
The controller does not have a fixed reference that a resistor divider trims. It reads five bits from the processor and sets the output from that code, so the rail voltage is defined by the load rather than by the board. On a repair or a legacy build this means the same controller can serve a different processor family without a resistor change, and it also means the code must be present before the rail comes up, or the output sits at its default and the processor never starts.
Crowbar blanking exists because the code can change while the rail is live. Without blanking, a transition from one VID code to another would look like an overvoltage and fire the crowbar, which is why the part holds off the protection for the duration of the transition.
Four phases and the current per phase
Each phase carries a fraction of the load, so a 4 phase configuration puts a quarter of the current through each inductor and each pair of FETs. That is what allows a 100 A core rail without a single large inductor. The active current balancing keeps the phases equal even when the FETs and the inductor resistances differ by a few percent, which they always do.
Sourcing position on a part like this
Parts built for processor core supplies age out of the catalogue before the boards that use them do, and the failure mode is a small quantity requirement with no catalogue stock. What we check before quoting is whether the part is a date coded original, whether the package is the TSSOP or the QSOP version, and whether the board needs the same VID default, because a substitution in this family is a board level decision rather than a socket decision.
When an order code in this family cannot be found, the obsolete part cross reference hub lists what else does the same job, the ADI second source page covers what to check before a part is dropped into an existing board, and component obsolescence management is the route we take on a live shortage.
Two questions buyers ask
Can the ADP3186 drive the FETs directly? No, the PWM outputs are logic level signals intended for external drivers. The gate drive stage is on the board, not in the controller.
What is the TSSOP version difference in the order code? JRUZ is the 28-lead TSSOP body. The QSOP version has a different suffix, and the two are not interchangeable on a board even though the die is the same.