Contact Us

ADP1823ACPZ

Brand: Analog Devices
Analog Devices ADP1823ACPZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADP1823ACPZ — Analog & Mixed-Signal ICs | Superb Automation

ADP1823ACPZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADP1823ACPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADP1823ACPZ: two interleaved buck rails from one 32-lead controller

The ADP1823ACPZ is a dual, interleaved, synchronous step down controller that takes a 3.7 V to 20 V supply input and drives two independent output rails from a power stage fed between 1 V and 24 V. It is a controller, not a converter: the switching elements are external N-channel MOSFETs, which is what allows the same part to carry a 1.2 V, 6 A rail and a 1.8 V, 8 A rail on one board without a heatsink. Interleaving the two phases 180 degrees apart is the reason the input capacitor can be smaller than the sum of two separate supplies.

Published values

ParameterValue
TopologyDual interleaved synchronous buck controller
Supply input range3.7 V to 20 V
Power stage input range1 V to 24 V
Switching frequency300 kHz, 600 kHz, or synchronised up to 1 MHz
Output accuracy0.85% from 0 C to 70 C
Current sensingLossless RDSON sensing across the low side FET
TrackingVoltage tracking for sequencing and DDR termination
Power goodIndependent POK output per channel
Shutdown supply current10 uA
ProtectionSoft start, current limit, thermal overload, reverse current during soft start
Package32-lead LFCSP, 5 mm x 5 mm

Interleaving changes the capacitor, not the load

Two phases switching at the same frequency and 180 degrees apart cancel part of the input ripple current, so the input capacitor sees a smaller RMS current than two independent regulators would produce. That is the reason a 12 V to 1.2 V and 1.8 V pair can share one 180 uF input bank in the published application circuit instead of two separate banks. The output capacitors are not shared, each rail still needs its own.

The synchronisation pin matters when the board has an RF or converter section. Running the two phases at 600 kHz and synchronising to an external clock up to 1 MHz keeps the switching products at a known frequency that can be filtered, instead of a free running beat between two supplies.

Lossless sensing and what it costs

The current limit is derived from the voltage across the low side MOSFET on resistance instead of a sense resistor. That removes a lossy element and a component, and it makes the limit depend on the RDSON of the FET, which rises with temperature. A limit set for 8 A at 25 C becomes a lower current limit at 100 C junction, so the FET has to be chosen with its hot RDSON in the calculation, not the cold figure on the front of the data sheet.

Tracking and power good in a multi rail board

Voltage tracking forces one rail to follow the other during start up, which is what a DDR termination or an FPGA core and IO pair needs to avoid a latch up path through the device. The independent power good outputs let the sequencer hold the next stage off until each rail is inside tolerance, so the order of rail rise is set by the board rather than by which regulator happens to start first.

Where a customer needs a second position on this part, the power management cross reference is the starting point, the ADI second source page sets out the checks a substitution has to pass, and OEM procurement is the short lead time route we quote against.

Two questions buyers ask

Can the ADP1823 be used for a single rail? Yes, one channel can be left disabled and the other used alone. The interleaving benefit disappears, but the part still works and the second channel stays available for a later revision.

Does it need an external 5 V bias? No, it has an internal linear regulator that supplies the gate drive from the supply input. That regulator is a source of heat at high input voltage and has to be checked against the junction temperature budget.