Contact Us

ADP1741ACPZ

Brand: Analog Devices
Analog Devices ADP1741ACPZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADP1741ACPZ — Analog & Mixed-Signal ICs | Superb Automation

ADP1741ACPZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADP1741ACPZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADP1741ACPZ: a 2 A regulator for 1.6 V to 3.6 V inputs, adjustable from 0.75 V to 3.3 V

The ADP1741ACPZ is the adjustable member of the ADP1740/ADP1741 pair, a CMOS low dropout regulator that runs from 1.6 V to 3.6 V and delivers up to 2 A. It exists for the rails that a 5 V LDO family cannot reach: nanometer FPGA I/O at 1.8 V, core rails down to 0.75 V, and DDR terminations where the input is already a low voltage bus. The adjustable version sets the output with two resistors, which is why the same order code reaches 0.75 V to 3.3 V while the fixed ADP1740 covers seven voltages.

Published values

ParameterValue
Maximum output current2 A
Input voltage range1.6 V to 3.6 V
Adjustable output range0.75 V to 3.3 V
Fixed options, ADP1740Seven values from 0.75 V to 2.5 V
Dropout at 2 A160 mV
Initial accuracy1%
Accuracy over line, load, temperature2%
PSRR65 dB at 1 kHz, 65 dB at 10 kHz, 54 dB at 100 kHz
Output noise at 0.75 V23 uV rms
Shutdown current2 uA
Output capacitor4.7 uF ceramic
ExtrasPower good output, soft start, reverse current protection

The input range is the constraint, not the output range

An input window of 1.6 V to 3.6 V means this part cannot be fed from a 5 V rail at all. On a board where the only available source is 5 V, a regulator from a different family is needed, and a substitute chosen on output current alone will be destroyed at first power up. The first line of any comparison table should be the input window, then the dropout, then the current.

At 2 A and 160 mV of dropout the dissipation is 0.32 W, which the LFCSP body handles with a copper area under the exposed pad. Running 2.5 V in to 0.75 V out at 2 A is 3.5 W and is a switching regulator job, not an LDO job.

What the four extra pins buy

Power good, soft start and reverse current protection are the reason this part is chosen over a three pin regulator on a board with several rails. Power good lets the sequencer hold the next rail off until this one is inside tolerance, and the soft start capacitor sets how fast the rail comes up so the inrush does not trip the upstream supply. Reverse current protection matters where a rail can be back fed by an IO that is powered before the regulator.

Substitution checks that catch most failures

The reference voltage and the divider tolerance decide the actual output, so a substitute with a 0.5 V reference instead of 0.8 V will produce a rail that is off by tens of percent with the same resistor values. The second check is the minimum output voltage, because adjustable parts differ in how low the reference allows the rail to go, and a core rail at 0.75 V has very little room. The third is the power good threshold and polarity.

The pages that answer this most often are the ADI second source page for the family alternatives, the pin to pin cross reference for the acceptance test, and component lead time solutions for the case where a replacement has to be fitted before the next build.

Two questions buyers ask

Can the ADP1741 be set to 1.0 V with two resistors? Yes, the adjustable range starts at 0.75 V and the output is set by the divider ratio against the internal reference. The divider values have to be calculated from the reference in the data sheet, not copied from another regulator.

Is the fixed ADP1740 a drop in for the adjustable ADP1741? No. They share a package family but the pin function at the adjust node differs, so the board has to be reworked before either can take the other.