ADP1613ARMZ
Product Specifications
ADP1613ARMZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADP1613ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADP1613ARMZ: the 2 A switch limit that separates it from the ADP1612
The ADP1613ARMZ is the higher current limit member of the ADP1612/ADP1613 step up pair, an 8-lead MSOP converter with an integrated switch, a 2.5 V minimum input and an output that can be set as high as 20 V. The two parts in the family are not interchangeable by name: the ADP1612 has a 1.4 A current limit and starts at 1.8 V, the ADP1613 has 2.0 A and starts at 2.5 V. On a TFT bias rail or a 12 V step up from a 3.3 V bus, that difference is the whole decision.
Published values
| Parameter | Value |
|---|---|
| Switch current limit | 2.0 A, against 1.4 A on the ADP1612 |
| Minimum input voltage | 2.5 V, against 1.8 V on the ADP1612 |
| Output voltage | Adjustable up to 20 V |
| Switching frequency | 650 kHz or 1.3 MHz, pin selectable |
| Efficiency | Up to 94% |
| Soft start | Adjustable with an external capacitor |
| Protection | Undervoltage lockout, thermal shutdown |
| Package | 8-lead MSOP, under 1.1 mm tall |
| Control scheme | Current mode PWM |
Current limit sets the load, not the data sheet headline
An integrated switch converter is limited by the peak current in the inductor, not by an output current rating printed on the first page. With a 2.0 A limit and a 3.3 V to 12 V step up, the usable output current is roughly the limit times the input to output ratio minus losses, so around 400 mA to 500 mA. Pushing a 12 V, 800 mA load onto this part will current limit at start up and drop out of regulation under load without ever looking like a fault. Sizing starts from the inductor ripple current and the limit, then checks the resulting output current against the load.
The frequency pin decides the inductor and the ripple
650 kHz allows a larger inductor with lower ripple and better light load efficiency. 1.3 MHz allows a smaller inductor and a smaller output capacitor in a thin display module, at the cost of higher switching losses. The pin is strapped, not programmed, so the choice is made once on the board, and a substitute converter with a fixed frequency has to be compared at the frequency the board was built for.
Where this part is used and what to check around it
TFT LCD bias supplies, portable instruments and industrial equipment are the published applications. The three things that fail first on a replacement are the inductor saturation current, the diode reverse voltage and the feedback divider tolerance, because a substitute with a different reference voltage will hold the rail a few percent off and still look stable on a meter.
For a board that has to keep running while a reel runs out, the power management cross reference is where the family alternatives sit, component obsolescence management is the check list before a substitute goes in, and BOM shortage recovery is how a gap is covered without a new line item.
Two questions buyers ask
Can the ADP1612 replace the ADP1613 in a shortage? Only if the load current fits inside the 1.4 A switch limit and the input rail never drops below 1.8 V. The lower limit also changes the start up behaviour, so the inrush and soft start have to be rechecked.
Does the part need an external diode? Yes, the switch is integrated but the rectifier is external, and its reverse voltage rating has to be above the output rail with margin for the switching overshoot.