ADP160AUJZ-3.3-R7
Product Specifications
ADP160AUJZ-3.3-R7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADP160AUJZ-3.3-R7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADP160AUJZ-3.3-R7: 560 nA of Quiescent Current and 255 mW of Heat at 5 V
The ADP160AUJZ-3.3-R7 is an ultralow quiescent current CMOS linear regulator from Analog Devices in the 3.3 V fixed output option. The published summary gives 560 nA of quiescent current with no load and 860 nA at a 1 uA load, a maximum output current of 150 mA, an input range of 2.2 V to 5.5 V, 195 mV of dropout at 150 mA, plus or minus 1 percent initial accuracy and plus or minus 3.5 percent over line, load and temperature, 15 fixed output options from 1.2 V to 4.2 V, 72 dB of power supply rejection at 100 Hz, shutdown current under 50 nA typical, stability with 1 uF ceramic input and output capacitors, an integrated output discharge resistor, and a 5-lead TSOT or 4-ball WLCSP package. The AUJZ suffix is the 5-lead TSOT in tape and reel.
Two parts in one data sheet number
The 560 nA quiescent figure and the 150 mA output figure do not belong to the same operating point, and a buyer who reads only one of them will mis-specify the part. At no load the regulator is a sleep current device: 560 nA at 5 V is 2.8 uW, which is 0.0006 percent of the 495 mW it delivers at full load. At 150 mA the same part is a resistive pass element with 195 mV of dropout, which is 1.3 ohm. Products that use it well are ones where the load is either nearly zero for years or near 100 mA for milliseconds, and products that use it badly ask it to hold 3.3 V at 5 V in continuously.
255 mW in a five lead package
From 5 V in to 3.3 V out at 150 mA the regulator dissipates 255 mW and converts 66 percent of the input power. From 5.5 V it is 330 mW and 60 percent. From 3.6 V, the top of a lithium cell, it is 45 mW and 92 percent. The five lead TSOT has a thermal resistance that turns 255 mW into a junction rise that the datasheet derates the load current for, so a 5 V rail feeding a 3.3 V regulator at full current is a heater with a regulator attached. Where 5 V is the only rail, a switching pre-regulator or a lower current load is the answer, not a bigger package.
Plus or minus 3.5 percent is 116 mV
The initial accuracy is plus or minus 1 percent, but the guaranteed window over line, load and temperature is plus or minus 3.5 percent, which on a 3.3 V output is 116 mV. A load that needs 3.3 V plus or minus 2 percent cannot be fed from this part over temperature, and the same load fed from a 1 percent reference plus a calibrated divider can. The 15 fixed output options are there so the window is spent on the load rather than on a resistor divider tolerance.
The discharge resistor and the shutdown pin
The ADP160 includes a switched resistor that discharges the output when the regulator is disabled, and the ADP162 is the identical part without it. On a rail that supplies a bus or a converter that must not float, the discharge is what makes the next power up deterministic, and it is a function that is otherwise built from a transistor and a resistor. Shutdown current is under 50 nA typical, so a system that holds the rail off for long periods keeps the battery.
Published figures
| Parameter | Value |
|---|---|
| Output | 3.3 V fixed, 150 mA maximum |
| Input range | 2.2 V to 5.5 V |
| Quiescent current | 560 nA no load, 860 nA at 1 uA |
| Dropout | 195 mV at 150 mA, 1.3 ohm |
| Accuracy | +/-1 percent initial, +/-3.5 percent over line, load, temperature |
| Dissipation at 5 V in | 255 mW at 150 mA, 66 percent conversion, derived here |
| Power supply rejection | 72 dB at 100 Hz |
| Capacitors | 1 uF ceramic input and output, stable |
| Shutdown current | Under 50 nA typical |
| Package | 5-lead TSOT, AUJZ, tape and reel |
Selection notes
- A 1 uF ceramic output capacitor and the internal discharge resistor are part of the specification, so a larger output capacitor changes the turn off behaviour rather than improving stability.
- Five fixed voltages in the family differ only in the internal divider, so a 3.0 V rail can be had without a board change beyond the order code.
- 72 dB of rejection at 100 Hz is 3981 to 1, and the rejection falls with frequency, so a switching converter ahead of it needs its ripple checked at the switching frequency and not at 100 Hz.
- The part is stable with ceramic capacitors because of an internal compensation scheme, which is the difference between it and older low dropout regulators that needed tantalum.
- For a rail that must bleed down, the ADP160 has the discharge resistor and the ADP162 does not.
Buyer questions
Is the 560 nA figure what the part draws at 150 mA? No. It is the no load quiescent current. At 150 mA the regulator draws 150 mA plus the quiescent current, and dissipates the input to output difference.
Can it run from a 5 V rail at full current continuously? It can deliver the current, and it dissipates 255 mW doing so, which the 5-lead TSOT only supports at a reduced ambient. The 3.6 V input case is the one the package was sized for.
Category page: Analog and mixed-signal ICs. For the regulator side of a power tree see power management cross reference, and for long lead time cover see component lead time solutions.
Request Quote — In Stock, 100% New & Original, Full Warranty