Contact Us

ADM7171ACPZ-3

Brand: Analog Devices
Analog Devices ADM7171ACPZ-3 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADM7171ACPZ-3 — Analog & Mixed-Signal ICs | Superb Automation

ADM7171ACPZ-3

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADM7171ACPZ-3 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADM7171ACPZ-3: the 1 A low noise LDO, and what the 5 uV figure actually covers

The ADM7171ACPZ-3 is the 8-lead LFCSP version of the ADM7171, a CMOS low dropout regulator rated 1 A from a 2.3 V to 6.5 V input. The headline number is 5 uV rms of output noise from 100 Hz to 100 kHz, and the detail that matters when the part is used on a converter rail is that the figure does not change with the output voltage setting, so the same part on a 1.8 V rail and on a 3.3 V rail quotes the same noise. Everything below is taken from the published data sheet so a buyer can check a substitute against it line by line.

Published values

ParameterValue
Maximum output current1 A
Input voltage range2.3 V to 6.5 V
Output noise, 100 Hz to 100 kHz5 uV rms, independent of VOUT
PSRR at 100 kHz60 dB
Dropout at 500 mA, VOUT = 3 V42 mV
Initial accuracy-0.5% to +1%
Accuracy over line, load, temperature1.5%
Quiescent current, no load0.7 mA
Shutdown current at VIN = 5 V0.25 uA
Output capacitor4.7 uF ceramic, stable
Fixed output options17 values from 1.2 V to 5.0 V, stock 1.3/1.8/2.5/3.0/3.3/4.2/5.0 V
Package8-lead LFCSP, 3 mm x 3 mm

Where the noise number starts and stops

The 5 uV rms is integrated from 100 Hz to 100 kHz. Below 100 Hz the noise per root hertz rises, so a front end that measures in the 0.1 Hz to 10 Hz band cannot use this figure to compare parts, it has to ask for the low frequency peak to peak value instead. The number is also quoted with a 4.7 uF ceramic output capacitor fitted; dropping to 1 uF raises the high frequency floor and moves the transient response, so a board that changes the capacitor to save space is no longer running the published condition.

For a converter or a PLL supply the useful part of the specification is the rejection at the switching frequency, and 60 dB at 100 kHz is the value to quote against a 1.3 MHz or 2.2 MHz rail where the fundamental sits well above the band that a low frequency PSRR curve shows.

Dropout, headroom and heat

42 mV of dropout at 500 mA with a 3 V output means the input only has to sit a little above the rail to stay in regulation at that current. At the full 1 A the dropout is larger and the 2.3 V minimum input applies to the low output settings, not to a 3.3 V rail that is being fed from a 2.5 V source.

The thermal side decides the input voltage more often than the dropout does. Dropping 5 V to 3.3 V at 1 A puts 1.7 W into a 3 mm by 3 mm package, which no ambient above 60 C will take without a copper area on the board and a lower input rail. In practice the part sits behind a switching pre regulator, and the LDO only cleans up the last few hundred millivolts.

Reading the order code

ACPZ is the 8-lead LFCSP body. The trailing digit after the dash is the factory trimmed output voltage; the stock list is 1.3 V, 1.8 V, 2.5 V, 3.0 V, 3.3 V, 4.2 V and 5.0 V, and the rest of the 17 options are special order, which is where lead time differences between otherwise identical parts come from. When a build needs 2.8 V it is worth checking whether the adjustable version set by two resistors is a shorter route than waiting for a factory trimmed voltage.

Applications that fit this part

ADC and DAC reference rails, precision amplifier supplies, PLL and VCO rails, clocking ICs, communications and infrastructure cards, medical front ends and industrial instrumentation. In every one of those the reason to pay for this part over a generic LDO is either the noise floor or the transient response to a fast load step, and 1.5 us for a 1 mA to 500 mA step is the second number to put in a comparison table.

When an order code in this family cannot be found, the power management cross reference lists what else does the same job, the ADI second source page covers what to check before a part is dropped into an existing board, and component lead time solutions is the route we take on a live shortage.

Two questions buyers ask

What output capacitor does the ADM7171 need? A 4.7 uF ceramic part, which is the condition the noise and stability figures are published under. A 1 uF capacitor will often start up on a bench, but it is outside the specified condition and the transient response quoted in the data sheet no longer applies.

Is the ADM7171 a drop in for the 2 A members of the family? The ADM7170 and the higher current parts share the family architecture and the LFCSP body, but pin function and thermal pad detail still have to be compared pad by pad against both data sheets before a board is released. We check that against the vendor document rather than against a distributor listing.