ADM3485EARZ-REEL7
Product Specifications
ADM3485EARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM3485EARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADM3485EARZ-REEL7: a 3.3 V Half Duplex RS-485 Transceiver with 15 kV of ESD Protection
What this part is
The ADM3485E is a half duplex RS-485 and RS-422 transceiver that runs from 3.3 V, moves data at 12 megabits per second, and carries plus and minus 15 kilovolts of electrostatic discharge protection on its bus pins. It has separate driver and receiver enable inputs, a receiver input impedance of 12 kiloohms which allows 32 nodes on one bus, and a fail safe receiver that outputs a logic high when the bus is open, which is the state a floating pair would otherwise resolve randomly.
The part is built for balanced transmission on multipoint buses: a disabled or unpowered driver tristates its output so it does not load the bus, thermal shutdown protects against bus contention, and the output is short circuit protected. The pinout follows the industry standard 75176 arrangement, so a board laid out for that footprint takes this part directly. The body is an eight lead narrow small outline, and the part is specified over the industrial temperature range. Applications are power and energy metering, telecommunications, electromagnetic interference sensitive systems, industrial control and local area networks.
Published figures that matter to a buyer
| Standard | TIA and EIA RS-485 and RS-422 compliant |
| Duplex | half, two wire |
| Supply | 3.3 V |
| Data rate | 12 megabits per second |
| ESD on bus pins | plus and minus 15 kilovolts |
| Nodes | up to 32 |
| Receiver input impedance | 12 kiloohms |
| Common mode range | minus 7 V to plus 12 V |
| Fail safe | receiver output high on a floating input |
| Protection | thermal shutdown, short circuit protection, tristate when disabled or unpowered |
| Pinout | industry standard 75176 |
| Body | 8 lead narrow small outline |
Where the headline numbers stop
Twelve megabits per second is 83.33 nanoseconds per bit, which is fast for a two wire bus and is only usable on a short cable with a termination at both ends. RS-485 does not have a data rate so much as a rate and distance pair, and a 12 megabit link over a hundred metres of unshielded pair will fail on reflections long before it fails on drive current. A meter or controller network that runs at 115 kilobit and a megabit is using a fraction of the part and getting the reliability of a slow edge.
Thirty two nodes at 12 kiloohms is 375 ohms of parallel receiver load, which sits on top of the termination. A bus with a 120 ohm termination at each end already presents 60 ohms, so the receiver load is a small part of the total; a bus at the node limit without termination presents 375 ohms and reflects. The 32 node figure is a standard limit rather than a target, and a network that reaches it should be checked for both termination and idle bias.
The 15 kilovolt figure is on the bus pins and it is an electrostatic discharge rating, which is a fast transient with a defined waveform. It is not a rating for a sustained fault: a 24 V supply shorted onto a data line is a different event, and a part that survives it is doing so by luck rather than by specification. The common mode range of minus 7 V to plus 12 V is the range over which the receiver still works, and it is 19 V wide on a 3.3 V part, which is what allows distant nodes to sit at different ground potentials.
Applications where it fits
- Electricity and gas meters on a two wire multidrop bus.
- Industrial controllers and remote input and output modules.
- Telecommunications equipment and cabinet alarms.
- Building networks where the cable runs near switching equipment and needs the protected part.
- Boards replacing an earlier 75176 footprint part that did not have the protection.
Two questions buyers ask
Is the unprotected part a cheaper alternative? The same family includes members without the E, and they cost less. The difference appears the first time a cable is plugged into a live connector or a nearby contactor opens: the protected part is specified to 15 kilovolts and the unprotected one is not. The saving is real and so is the field return rate.
What does the fail safe feature actually guarantee? That the receiver output goes high when the bus is open or floating, which is the state between transactions. It does not guarantee a defined output when the bus is terminated but no driver is active and the differential voltage sits near zero; that case needs the idle bias network that RS-485 practice puts on the bus.
Sourcing notes and next step
ADM3485EARZ-REEL7 is the eight lead narrow small outline in tape and reel. The E in the code is the protection level, the A is the grade and the RZ is the body, so three fields of the order code each change something that matters on the board or in the field. The 75176 pinout means a socket change is not needed, which is also why this part appears in so many second source requests. The analog and mixed signal IC family page lists the interface line, the defence grade components page covers the traceability a long life program expects, and the second source page sets out what a transceiver substitution has to be measured on.
Request Quote — In Stock, 100% New & Original, Full Warranty