ADM1485ARZ
Product Specifications
ADM1485ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADM1485ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADM1485ARZ: thirty megabit RS-485 on a five volt supply
The ADM1485ARZ is the fast member of the 8-lead RS-485 pair whose slower sibling is the ADM485. It runs at 30 Mbps from a single 5 V rail with a -7 V to +12 V common mode range, and the A suffix on this order code is the industrial temperature grade rather than the commercial one.
Published values
| Parameter | Value |
|---|---|
| Function | half duplex RS-485 driver and receiver |
| Supply | single 5 V |
| Data rate | 30 Mbps |
| Common mode range | -7 V to +12 V |
| Driver differential output | 2.0 V minimum, 5.0 V maximum into 50 ohm |
| Driver propagation delay | 10 ns typical |
| Receiver propagation delay | 15 ns typical |
| Temperature grade | -40 C to +85 C |
| Package | 8-lead narrow SOIC |
Thirty megabits against a 33 ns bit
At 30 Mbps one bit is 33.3 ns. The driver delay is 10 ns and the receiver delay is 15 ns, so the two together are 25 ns before any cable is counted, which is 75 percent of a bit period. The part meets its specification, and the number is the reason a 30 Mbps link is a backplane link and not a 100 m field bus link.
On a 10 m cable with a propagation velocity of about 5 ns per metre, the round trip is 100 ns, three bit periods. Any reflection has to settle inside one bit, which means the termination has to be at both ends and the stubs have to be short. At 5 Mbps the same cable gives 200 ns per bit and the tolerances are comfortable.
Why the slow part is often the right part
The ADM485 and the ADM1485 share the 8-lead footprint and the 5 V supply. The slower part has a limited slew rate, which lowers radiated emissions and makes a long, poorly terminated line behave; the faster part has faster edges and a shorter bit, which is what a short backplane needs and what a long cable punishes.
A buyer replacing one with the other has to read the data rate requirement first and the emission requirement second. The two order codes are not interchangeable in a system, and the difference does not show up on a bench test with a short cable.
Temperature grade and the A suffix
ARZ is the industrial grade, -40 C to +85 C, against the 0 C to +70 C of the JRZ part. The silicon and the footprint are the same; the difference is the tested range and the price. A board specified for outdoor equipment cannot use the commercial suffix even if the bench works.
The driver output into 50 ohm is bounded at both ends, 2.0 V minimum and 5.0 V maximum, and that upper bound is a common mode requirement rather than a power limit: an unbounded driver would push the bus outside the receiver window of the other nodes.
Sourcing and second source
This footprint is built by several vendors, so a second source is usually available within days rather than weeks. The checks are data rate, common mode range, temperature grade, then the receiver behaviour with an idle bus, because fail safe is not universal on this footprint.
The pages below hold the family cross reference, the acceptance routine and the shortage route.
The pages that answer this most often are the pin to pin cross reference for the family alternatives, the ADI second source page for the acceptance test, and how to verify a drop in replacement for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Is the ADM1485ARZ a drop in replacement for the ADM485JRZ? The footprint and the function are the same, but the data rate and the temperature grade differ. A board that only needs 5 Mbps can use either; a board specified over the industrial range cannot use the J suffix.
How many nodes can sit on the bus? The transceiver presents one unit load, so the node count is set by the standard limit for unit loads. The isolated members of the family present a fraction of a unit load and allow more.