Contact Us

ADG733BRUZ

Brand: Analog Devices
Analog Devices ADG733BRUZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG733BRUZ — Analog & Mixed-Signal ICs | Superb Automation

ADG733BRUZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG733BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG733BRUZ: three SPDT switches with break before make, 2.5 ohm typical on a 3 V or 5 V rail

The ADG733BRUZ is the triple SPDT member of the ADG733/ADG734 pair. Each of the three switches is independently selectable, 2.5 ohm typical on resistance, fully specified at 3 V, 5 V and plus or minus 2.5 V, and every channel breaks before it makes. It is the part for a board that has to hand three signals between two paths, such as two audio sources into one amplifier, or a calibration path and a measurement path into one ADC input.

Published values

ParameterValue
Configurationthree independently selectable SPDT switches
Supply1.8 V to 5.5 V single, plus or minus 2.5 V dual
On resistance2.5 ohm typical, 4.5 ohm maximum at 25 C
Flatness0.5 ohm
Leakage100 pA
Switchingbreak before make guaranteed
Quiescent powerbelow 0.01 microwatt
Package16-lead TSSOP or QSOP

Why break before make is the specification that matters

Two paths that overlap for a few nanoseconds short the A and B sources together. On an audio path that is a click. On a transducer drive it is a current spike through two output stages that were never meant to see each other. The ADG733 guarantees the break interval, so a source that cannot survive a short is safe even when the control line is switched asynchronously from a microcontroller pin.

The guarantee is only useful if the digital side cannot chatter. A control line that crosses the threshold slowly, from an RC or a long cable, can produce multiple transitions in one edge and multiple break make cycles. A Schmitt trigger buffer in front of the logic pins is the cheap fix.

What 2.5 ohm means at the load

Into 10 kohm the switch is 0.025 percent of the divider and is invisible. Into 600 ohm it is 0.4 percent, the order of a 1 percent resistor. Into 32 ohm headphones it is 7 percent, which is audible as a level change and is the point where a 0.5 ohm part such as the ADG821 belongs instead.

Flatness of 0.5 ohm is the figure that sets distortion, not the absolute value: a switch whose resistance moves with signal level modulates the gain and turns a clean sine into harmonics. The 0.5 ohm window over the full analog range is what makes the part acceptable on a line level audio path.

Supply choices

The part is specified on a 5 V single rail, a 3 V single rail and plus or minus 2.5 V, so a bipolar signal that swings below ground needs the dual rail and cannot be passed on a single 5 V supply. A rail to rail claim on a single supply means 0 V to VDD and nothing below, which is a common source of a clipped negative half cycle on a first prototype.

Quiescent power below 0.01 microwatt is a leakage figure. The part draws nothing worth counting when idle, so the supply decision is driven by the signal swing and not by current budget.

For a board that has to keep running while a reel runs out, the obsolete part cross reference hub is where the family alternatives sit, vendor consolidation is the check list before a substitute goes in, and one stop BOM sourcing is how a gap is covered without a new line item.

Two questions buyers ask

Can the ADG734 replace the ADG733? Only if the board has room for four switches and the extra channel is left unconnected. The ADG734 is the quad of the same family with the same 2.5 ohm switch and the same control interface, but it is a 20-lead part against the 16-lead ADG733.

Does the switch pass signals below ground on a single supply? No. On a single 5 V rail the analog range is 0 V to VDD. For a bipolar signal the dual rail version is required, and the dual rail is specified at plus or minus 2.5 V, not at plus or minus 5 V.