ADG723BRMZ
Product Specifications
ADG723BRMZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG723BRMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG723BRMZ: one normally open and one normally closed switch on a single control line
The ADG723BRMZ is the mixed pair of the ADG721/ADG722/ADG723 family. Switch one closes on a logic high and switch two closes on a logic low, so one control line hands a signal from one path to the other without an inverter or a second GPIO. The vendor publishes 4 ohms maximum on resistance at 5 V and 10 ohms maximum at 3 V, with 20 ns turn on and 10 ns turn off. There is no negative rail and no charge pump, which is why the part appears in handheld instruments, USB 1.1 front ends and battery powered sample paths.
Published values
| Parameter | Value |
|---|---|
| Supply | 1.8 V to 5.5 V single supply |
| On resistance | 4 ohms maximum at 5 V, 10 ohms maximum at 3 V |
| Switch time | tON 20 ns, tOFF 10 ns |
| Bandwidth | -3 dB above 200 MHz |
| Quiescent power | below 0.1 microwatt |
| Digital input | TTL and CMOS compatible |
| Package | 8-lead MSOP or 3 mm x 2 mm LFCSP |
Why the pair is worth paying for
A board that shares one connector between two sources usually needs the two paths to be complementary: when A is on, B must be off. With the ADG723 that is one wire. With two single switches it is one wire plus a logic inverter, and the inverter adds a propagation delay that matters when the control signal comes from a slow opto or a long cable.
The pair is also useful on a shared bus where a fault on one side should not reach the other. Switch one and switch two are never closed at the same moment, so a short on the B side cannot be coupled onto the A side through the package.
What 4 ohms does to a divider
Four ohms in series with a 1 kohm load is 0.4 percent of the divider, which is already larger than the 0.1 percent resistors a 12 bit instrumentation channel is usually built with. Into 10 kohm the same switch is 0.04 percent and disappears under the resistor tolerance. Into 150 ohm it is 2.6 percent, which is the range where a 4 ohm part stops being transparent and a 1 ohm part such as the ADG821 has to take over.
At 3 V the maximum is 10 ohms, so a board that runs from a 3 V coin cell as well as a 5 V rail sees the error grow by two and a half times on the battery. That is a line item worth checking on the bench rather than taking from a room temperature figure.
Checks before a build
Turn on of 20 ns against a 200 MHz bandwidth, a 5 ns period, means the switch is four periods slow at the top of its pass band: the part passes the signal but cannot be used as a fast gate at that frequency. Used as a static path selector it is far quicker than the control loop that drives it.
Power is quoted below 0.1 microwatt, which is the leakage term rather than the switching term, so the control line should be driven from a rail that actually reaches 0 V and VDD. A control input parked at 1.2 V on a 5 V rail sits in the undefined band and both switches can conduct.
Where it fits
USB 1.1 signal switching, reed relay replacement, audio and video routing in portable gear, and sample paths that are already gated slowly. For a differential sensor front end the matching between the two switches inside one package is better than between two packages, which is the reason to keep both paths on the same ADG723 rather than two ADG721.
When an order code in this family cannot be found, the pin to pin cross reference lists what else does the same job, how to verify a drop in replacement covers what to check before a part is dropped into an existing board, and component lead time solutions is the route we take on a live shortage.
Two questions buyers ask
Is the ADG723 a drop in for the ADG721? No. Same supply, same package and same 4 ohm switch, but the control polarity is mixed: the ADG721 is two normally open switches and the ADG722 is two normally closed ones. A board built for the ADG721 will invert its truth table if an ADG723 is fitted.
What happens if the control pin floats? Switch one is defined by a pull to the rail, and the part has no internal pull on the digital input. A floating control pin leaves the input in the undefined band, both switches can conduct, and the isolation the part is bought for is lost. Fit a 100 kohm pull to the state the board should power up in.