Contact Us

ADG453BRZ-REEL7

Brand: Analog Devices
Analog Devices ADG453BRZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG453BRZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG453BRZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG453BRZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG453BRZ-REEL7: A 4 ohm Quad Switch Read as a Divider Error

What this part is

The ADG453 is a monolithic quad single pole single throw analog switch on a linear compatible CMOS process. Analog Devices rates the on resistance at 4 ohm typical with 0.2 ohm of flatness, allows a 44 V maximum supply and a plus or minus 15 V analog signal range, and specifies the part at plus or minus 5 V, +12 V and plus or minus 15 V. The 16-lead body is pin compatible with the older ADG412 and ADG432 numbers, which is why it shows up as a drop-in upgrade in signal routing boards that were laid out years ago. The quiescent power of 18 uW is what makes it usable in a battery instrument that switches a sensor between channels every few milliseconds.

Published figures that matter to a buyer

Switch on resistance4 ohm typical, 5 ohm family figure
On resistance flatness0.2 ohm over the signal range
Maximum supply44 V
Analog signal rangeplus or minus 15 V
Supply combinations specifiedplus or minus 5 V, +12 V, plus or minus 15 V
Quiescent power18 uW
Continuous current100 mA
Switching timeTurn on under 70 ns, turn off under 60 ns
ESD2 kV
Logic inputTTL and CMOS compatible
Package16-lead DIP, SOIC and Cerdip
Pin compatibilityUpgrade for ADG412 and ADG432

Where the headline numbers stop

A switch is a resistor in series with the signal, so the number that matters is the ratio of that resistance to the load it drives. Four ohm into a 100 ohm load is a 3.85 percent gain error that moves with temperature and with signal level, and 4 ohm into a 10 kohm load is 0.04 percent, which is why this part belongs in high impedance routing and not in a 50 ohm path. The 0.2 ohm flatness is the part of the error that does not cancel in a ratiometric measurement, and it is 5 percent of the on resistance.

The 100 mA continuous rating is a package and channel limit, not a load specification: 100 mA through 4 ohm is 40 mW inside the switch and 0.4 V of drop, which would corrupt any low level signal sharing the same path. The 44 V maximum supply allows plus or minus 22 V rails but the signal range is specified to plus or minus 15 V, so the extra rail headroom is for transients and not for a larger signal. Switching times of 70 ns and 60 ns set the fastest useful multiplex rate only after the settling of the source and the load are counted, which in a 12 bit system is usually an order of magnitude slower.

Applications where it fits

  • Sensor multiplexing in data acquisition front ends where the source impedance is high and 4 ohm is negligible.
  • Gain and range switching in instrumentation amplifiers, where the switch sits inside a feedback network.
  • Signal routing in test equipment that has to pass plus or minus 15 V without a relay.
  • Replacement of ADG412 and ADG432 sockets where the board cannot be reworked.

Two questions buyers ask

Is the switch action the same as the part it replaces? The quad family is offered in normally open and normally closed variants, and the part number decides which. A substitute with the opposite action powers up with the signal connected instead of disconnected, so the ordering guide has to be checked rather than the pin count.

Does the on resistance matter if the load is a converter input? A successive approximation converter with a switched capacitor input presents a load that changes during the acquisition window, so the switch resistance and the source capacitance form the settling time constant. At 4 ohm and a few tens of picofarads the time constant is short, but a 10 kohm source behind the switch dominates and has to be buffered.

Sourcing notes and next step

The ADG453BRZ-REEL7 is the SOIC body on tape and reel, and the same function is offered in DIP and Cerdip for through hole and high temperature boards. Because the family is pin compatible across several generations, a substitution question is usually answered by the switch action and the supply range rather than by the pinout. We source the family with date code and package recorded, and we can quote the through hole body where the board is older. The analog and mixed signal IC family page lists the switch and multiplexer line, the drop-in replacement verification page covers the substitution check, and the BOM shortage recovery page handles the case where the exact suffix is unavailable.

Request Quote — In Stock, 100% New & Original, Full Warranty