ADG453BRZ
Product Specifications
ADG453BRZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG453BRZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG453BRZ: quad SPST switch with two channels of each logic polarity
The ADG453BRZ is the mixed polarity member of the ADG451 family: two of its four switches close with a logic low, like the ADG451, and the other two close with a logic high, like the ADG452. It keeps the 4 ohm on resistance, the 0.2 ohm flatness, the plus or minus 15 V signal range and the 44 V supply rating, and it adds break before make action between the switches, which the other two members of the family do not specify.
Published values
| Parameter | Value |
|---|---|
| Configuration | 4 SPST switches, two of each control polarity |
| On resistance | 4 ohm |
| On resistance flatness | 0.2 ohm |
| Supply range | up to 44 V total |
| Analog signal range | plus or minus 15 V |
| Continuous current | 100 mA per channel |
| Switching action | break before make |
| Turn on time | 70 ns |
| Turn off time | 60 ns |
| Power dissipation | 18 uW |
| Package | 16-lead SOIC_N |
Two polarities in one body is a muting function
A signal path that has to swap between two sources while the other is muted needs one switch that closes and one that opens from the same control line. The ADG453 gives that in a single package: drive the control high and the normally open channel conducts while the normally closed one releases. Four switches of mixed polarity therefore make a two channel changeover without an inverter on the board.
The break before make behaviour is what makes the changeover safe. Without it, the moment when both switches conduct connects the two sources together, and two low impedance outputs driving each other is a current spike that shows up as a click in audio and as a fault in a measurement channel.
Where 4 ohm is and is not invisible
Into a 10 kohm load the switch is 0.04 percent of the path, which is below the error of most converters. Into a 600 ohm load it is 0.7 percent, and into a 50 ohm load it is 8 percent. The same part is therefore transparent in an instrument input and a significant element in a signal chain that drives a low impedance, and the specification has to be read against the load rather than on its own.
The 0.2 ohm flatness is the ac figure. It changes the resistance by 5 percent across the signal swing, so a 1 V signal into a 1 kohm load picks up a 0.2 mV amplitude modulation, which is a distortion term at the signal frequency and its harmonics rather than a gain error.
Charge injection and the sample and hold
Every switch transfers a small packet of charge from the digital control to the analog path when it opens. That charge lands on the hold capacitor of a sample and hold and appears as a step. A 10 pF hold capacitor with a few picocoulombs of injection moves by hundreds of millivolts, which is why a sample and hold built around a switch needs either a larger capacitor or a differential topology that cancels the step.
The part is specified at plus or minus 5 V, 12 V and plus or minus 15 V, so the same order code can be qualified at three operating points. A board that runs at 12 V single supply has its own column in the table, which is the reason the datasheet is longer than the feature list suggests.
When an order code in this family cannot be found, the obsolete part cross reference hub lists what else does the same job, how to verify a drop in replacement covers what to check before a part is dropped into an existing board, and one stop BOM sourcing is the route we take on a live shortage.
Two questions buyers ask
How do I know which of the four switches is normally closed? The pinout in the data sheet labels each control input and its switch, and the two polarities are fixed by the die. A board that needs a different assignment cannot swap them in software, so the pin table has to be read before the part is soldered before the part is soldered.
Is the ADG453 a drop in for the ADG451? The package and the pinout match, but the control polarity of two switches is inverted. Fitting one where the other is expected leaves two channels in the wrong state at power up.