Contact Us

ADG1612BCPZ-REEL7

Brand: Analog Devices
Analog Devices ADG1612BCPZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1612BCPZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG1612BCPZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1612BCPZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG1612BCPZ-REEL7: 1 Ohm Typical, 1.6 Ohm Over Temperature, and the 60 Percent Between

The ADG1612 contains four independent single pole single throw switches in one body. Typical on resistance is 1 ohm and the maximum over temperature is 1.6 ohm, with 0.2 ohm of flatness across the signal range. The switch runs from plus or minus 3.3 V to plus or minus 8 V dual supplies or 3.3 V to 16 V single, needs no separate logic rail, and accepts 3 V logic with a 2.0 V high threshold and a 0.8 V low threshold. THD plus noise is 0.007 percent and static dissipation is below 16 nW. The BCPZ order code is the 16-lead LFCSP.

Worst case is 60 percent above the headline

1.6 ohm against 1 ohm is a 60 percent rise from the typical figure to the guaranteed one, and the 0.2 ohm flatness is 20 percent of the typical on resistance. Whether that matters is a question about the load:

ParameterValue
Configuration4 independent SPST switches
On resistance1 ohm typical, 1.6 ohm maximum over temperature
On resistance flatness0.2 ohm
Dual supplyplus or minus 3.3 V to plus or minus 8 V
Single supply3.3 V to 16 V
Logic supplynone required, 3 V compatible inputs
Logic thresholdsVIH 2.0 V, VIL 0.8 V
DistortionTHD plus N 0.007 percent, or minus 83.1 dB
Static dissipationbelow 16 nW
Bodies16-lead TSSOP and 16-lead 4 by 4 mm LFCSP

Into a 10 kohm load the typical resistance is 0.010 percent of gain and the worst case is 0.016 percent, both invisible. Into 1 kohm they are 0.100 and 0.160 percent. Into 100 ohm they are 0.990 and 1.575 percent, and at that point a buyer who quoted from the typical number is short by half a percent of gain over temperature. The flatness term is smaller than the absolute term in every case, 0.020 percent into 1 kohm and 0.200 percent into 100 ohm.

Logic polarity is the trap on this family

The ADG1611 and the ADG1612 are the same silicon with inverted control logic: the 1611 closes a switch on logic 0, the 1612 on logic 1. The ADG1613 mixes both polarities in one body. A part number substitution across that family changes the state of every switch at power up, so the polarity belongs in the quotation line as much as the resistance does.

Where the small numbers land in a signal path

A static dissipation below 16 nW corresponds to 3.2 nA of supply current at 5 V, so the switch is a contact in the standby budget. The 0.007 percent distortion figure is tied to the flatness, not to the absolute resistance, which is why the vendor quotes it with a signal level and a load attached rather than as a property of the part.

Selection notes

  • Rail to rail signal range, and the off state blocks signals up to the supplies.
  • Each switch conducts equally well in both directions when closed.
  • No VL pin, so a 3 V processor drives it directly from a single logic threshold.
  • The 4 by 4 mm LFCSP and the TSSOP share the pinout across bodies, which keeps a second source on one footprint.

Buyer questions

Is the ADG1612 a drop-in replacement for the ADG1611? On the footprint yes, on the firmware no. The control logic is inverted, so the same board with the other part switches every channel the wrong way round at a given logic level.

Can it switch a plus or minus 10 V signal? The dual supply range reaches plus or minus 8 V, so the total span is 16 V and a plus or minus 8 V signal fits. A plus or minus 10 V signal needs a switch with a wider supply range.

Family page for the category: Analog and mixed-signal ICs. For drop-in alternatives see pin-to-pin cross reference, and for consolidating switch and amplifier lines into one shipment see BOM shortage recovery.

ADG1612BCPZ-REEL7: the suffix decides the logic polarity, not the grade

ADG1611 and ADG1612 contain the same four single pole single throw switches and differ only in the control logic: the 1611 turns on with a logic zero and the 1612 turns on with a logic one. That makes the part number a firmware and fail safe decision rather than a performance step, and it is the first thing to check when an invoice shows a substitute that looks electrically identical. On a board that must default to a safe state with the controller held in reset, the polarity decides which of the two parts is the safe one.

ItemPublished valueArithmetic or consequence
On resistance1 ohm typical, 1.6 ohm maximum over temperature60 percent rise from typical to the guaranteed limit
Flatness0.2 ohm20 percent of typical, which is the distortion term
SupplyPlus or minus 3.3 V to plus or minus 8 V, 3.3 V to 16 V singleA 24 V industrial rail is outside the family
Logic3 V compatible, 2.0 V high, 0.8 V lowNo separate logic supply to route or to sequence
DistortionTHD plus noise 0.007 percentAbout 13 usable bits on an audio band signal
Polarity1612 on with logic 1, 1611 with logic 0The two codes are not interchangeable on a fixed netlist
Body16-lead TSSOP or LFCSPThe reel suffix follows the body

One ohm typical against 1.6 ohm maximum is the tolerance a budget sees

A gain switching network built on a one ohm typical switch has a 60 percent error band between a typical sample and a guaranteed one, and that band is what a production test has to accept. The flatness of 0.2 ohm over the signal range is the term that produces distortion, and it is the reason this part family is quoted with a total harmonic distortion figure at all. Into a 1 kohm load the 1.6 ohm maximum is 0.16 percent of gain error, and into 10 kohm it is 0.016 percent.

Charge injection is the sample and hold question

The vendor describes low charge injection as a feature without a number in the heading, so the value belongs to the data sheet table and should be read before the part is used ahead of a high resolution converter. The practical check is the size of the hold capacitor: the same injected charge produces a step that scales inversely with capacitance, so a 10 pF hold capacitor sees ten times the step of a 100 pF one.

Buying this order code

Because the polarity differs between two otherwise identical codes, a substitute has to be checked for the logic sense before anything else, and that check is described on the drop in verification page. The switch family is listed on the analog line card, and a shortfall on the 16-lead body is handled through the shortage desk rather than by taking the 1611.

Request Quote — In Stock, 100% New & Original, Full Warranty