ADG1608BRUZ
Product Specifications
ADG1608BRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1608BRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1608BRUZ: an 8 to 1 CMOS multiplexer with 4.5 ohm on resistance and a 16 V single supply
The ADG1608BRUZ is the eight channel to one multiplexer of the ADG1608/ADG1609 family, built on a CMOS process with a wider supply window than the iCMOS parts: 3.3 V to 16 V single supply or 3.3 V to 8 V dual. On resistance is 4.5 ohm typical with 1 ohm flatness, continuous current is up to 470 mA, and the digital inputs accept 3 V logic without a logic rail.
Published values
| Parameter | Value |
|---|---|
| Configuration | 8 single ended channels to 1 output |
| On resistance | 4.5 ohm typical |
| Flatness | 1 ohm |
| Continuous current | up to 470 mA |
| Supply | 3.3 V to 16 V single, 3.3 V to 8 V dual |
| Logic | 3 V compatible, no VL supply required |
| Package | 16-lead TSSOP or 3 mm x 3 mm LFCSP |
The supply window is the reason to pick this part
Many multiplexers are specified at plus or minus 15 V and nothing else, which forces a dual rail onto a board that only has 12 V. This part is specified from 3.3 V to 16 V single supply and from 3.3 V to 8 V dual, so the same order code covers a 5 V system, a 12 V system and a plus or minus 5 V system. On a product family that spans those rails, one part number replaces three.
The 16 V single supply ceiling also sets the maximum signal: a 12 V industrial loop sits inside the range with headroom, and a 24 V loop does not. For a 24 V system the ADG5208 family, which is rated to a 40 V single supply, is the one to look at.
What 470 mA really means
At 470 mA through the 4.5 ohm typical resistance the drop is 2.1 V and the dissipation is nearly 1 W. No 16-lead package holds 1 W continuously at an elevated ambient, so the current figure is a rating for a short duty or for a low ambient with a solid copper pad under the part. A board that draws 470 mA continuously should measure the case temperature before it accepts the number.
At a tenth of that current, 47 mA, the drop is 0.21 V and the dissipation is 10 mW. That is the regime where the part is comfortable, and it is where most signal path applications actually sit.
Flatness and the eight channel scan
One ohm of flatness on a 4.5 ohm switch is a 22 percent modulation of the series resistance over the signal range. On a path where the switch is in series with a high impedance converter input that is irrelevant, because almost no current flows. On a path where the switch feeds a 50 ohm load the same modulation is a visible gain change with signal level.
For a scanning front end the useful check is the channel to channel consistency at mid scale after the converter settles, because a multiplexer that is working correctly gives eight readings that differ only by the sensor, and one that is not gives a repeatable offset on one channel that follows the address.
Sourcing notes for this family: one stop BOM sourcing holds the cross references, component lead time solutions is the pre substitution check, and how to verify a drop in replacement is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Can the ADG1608 run on a 3.3 V analog supply? The supply range starts at 3.3 V, but the on resistance rises as the rail falls and the 4.5 ohm headline is not the 3.3 V figure. The error budget for a 3.3 V system has to be built from the low supply column of the data sheet.
What replaces the ADG1608 for a 24 V system? A part in the high voltage family rated to a 40 V single supply, which also carries latch-up proof construction and a higher electrostatic discharge rating at the input pins. The pin function is not the same, so the board changes.