ADG1412YRUZ-REEL7
Product Specifications
ADG1412YRUZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1412YRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
ADG1412YRUZ-REEL7: 1.5 Ohm switches, and the logic polarity that breaks a swap with the ADG1411
The ADG1412YRUZ-REEL7 is a quad single pole single throw analog switch built on a high voltage process, with 1.5 Ohm of on resistance, 0.3 Ohm of on resistance flatness and 0.1 Ohm of match between channels. The code reads ADG1412 for the part, RU for the 16-lead TSSOP body, Z for the RoHS finish and REEL7 for the 7 inch reel. It is specified at plus 12 V, plus and minus 15 V and plus and minus 5 V, takes 3 V logic inputs, and needs no separate logic supply pin.
The detail that decides most substitutions is not electrical. The vendor page states that the ADG1411 and the ADG1412 differ only in that the digital control logic is inverted: the ADG1411 turns a switch on with a logic 0 and the ADG1412 turns it on with a logic 1. The two parts share a footprint and a specification table, so a buyer comparing only the resistance figures will treat them as interchangeable, and a firmware image written for one will invert every channel on a board built with the other.
What the vendor page states
| Parameter | Value |
|---|---|
| Configuration | four independently selectable SPST switches |
| On resistance | 1.5 Ohm typical |
| On resistance flatness | 0.3 Ohm |
| Match between channels | 0.1 Ohm |
| Continuous current | 250 mA per channel in the LFCSP, 190 mA in the TSSOP |
| Supplies | plus 12 V, plus and minus 15 V, plus and minus 5 V |
| Logic | 3 V compatible, no VL supply required, on with logic 1 |
| Signal range | rail to rail, bidirectional when on |
| Qualification | AEC-Q100 for automotive applications |
| Packages | 16-lead TSSOP, 16-lead 4 mm by 4 mm LFCSP |
Reading the resistance figures against the load
1.5 Ohm in a 1 kOhm signal path is 0.15 percent, which is invisible in almost any measurement. The same 1.5 Ohm in a 50 Ohm path is 3 percent, which is a level error worth calculating. Flatness of 0.3 Ohm is 20 percent of the on resistance, and it is flatness rather than absolute value that produces distortion when the signal swings across the range: a switch that changes resistance as the signal moves modulates the signal with itself. Match of 0.1 Ohm between channels produces 1 mV of difference at 10 mA of channel current, which is what matters in a differential path that relies on two channels tracking.
Current carrying and what the package allows
190 mA continuous in the TSSOP through 1.5 Ohm is 54 mW per channel; the LFCSP allows 250 mA, which is 94 mW. The figure that has to be used for a thermal check is not the typical resistance but the maximum over temperature, which the vendor lists at 2.6 Ohm, so the worst case dissipation at 250 mA is 163 mW per channel. Four channels all carrying that current in one TSSOP is a thermal question about the board, not about the switch, and it is the reason the current rating is quoted per package rather than per part.
The logic polarity question, in practice
A board built around the ADG1411 and built with the ADG1412 will have all four switches in the opposite state from the firmware's intent. On a signal routing application that shows up as the wrong channel selected; on a sample and hold it shows up as a held value that never updates. The fix is either a firmware change or a different part, and the check belongs in the incoming inspection, not in the failure analysis.
What to confirm before ordering
The polarity field first. Then the package, because the current rating differs between the TSSOP and the LFCSP and the two are not footprint compatible. Then the supply configuration, since the part is specified at three different supply sets and the on resistance figures are per supply. Where the application needs break before make, that is the ADG1413 rather than this part, and the vendor page states it explicitly.
Switch and multiplexer families are indexed under Analog and mixed-signal ICs, footprint compatible parts from other vendors are listed in the pin to pin cross reference, and where a specific package is on allocation the component lead time page tracks the position.
Request Quote — In Stock, 100% New & Original, Full Warranty