ADG1412YRUZ
Product Specifications
ADG1412YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1412YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1412YRUZ: The Same Quad Switch with Inverted Control, Chosen for What Happens at Reset
The ADG1412YRUZ is the second member of the quad switch family, identical to the ADG1411 in every electrical respect except one: its switches close on a logic one instead of a logic zero. That single inversion is the whole difference between the two order codes, and it is the reason both exist. On resistance is 1.5 ohm typical with 0.3 ohm of flatness and 0.1 ohm of channel to channel match, continuous current is 190 mA per channel in the 16-lead TSSOP body, the part is specified at plus 12 V, at plus and minus 15 V and at plus and minus 5 V, needs no logic supply, accepts 3 V logic and is AEC-Q100 qualified.
Reset state is a real specification
A processor pin is not defined until the processor boots. Some parts drive low, some float, some are pulled up by a resistor on the board. With the ADG1411, a low level closes the switch, so a pin that sits low through reset connects the signal path; with the ADG1412, the same low level leaves the switch open. In a system where a transducer must not be connected to an amplifier during power-up, or where two sources must not be paralleled before the controller is ready, the polarity decides whether the board is safe during the first milliseconds. That is why the two parts are stocked as separate codes with separate prices rather than as one part with a strap.
Current rating follows the package, not the die
The same silicon is rated 250 mA in the 4 mm by 4 mm LFCSP and 190 mA in the 16-lead TSSOP, and this order code is the TSSOP. The difference is thermal: the LFCSP has an exposed pad that solders to copper, while the TSSOP dissipates through its leads. At 1.5 ohm and 190 mA the conduction loss per channel is 54 mW, and four channels at that current dissipate 216 mW, which in a narrow body is already a temperature rise worth calculating. A product that needs the full 250 mA should move to the LFCSP body and provide the copper underneath it.
| Parameter | Value on this order code | What it decides |
|---|---|---|
| Configuration | Four single pole single throw switches | Independent control of four paths |
| Control polarity | Logic one closes the switch | Open at reset when the drive pin is low |
| On resistance | 1.5 ohm typical | 54 mW per channel at 190 mA |
| Flatness and match | 0.3 ohm and 0.1 ohm | Distortion and differential balance terms |
| Continuous current | 190 mA in the TSSOP body | 216 mW for all four at full current |
| Supply conditions | 12 V, plus or minus 15 V, plus or minus 5 V | Choose a specified rail, not one in between |
| Logic supply | None, 3 V compatible | Drives from a modern processor directly |
| Signal range | Rail to rail | Cannot switch above the supplies |
| Qualification | AEC-Q100 | Automotive builds |
| Package | 16-lead TSSOP | Lower current than the LFCSP sibling |
Matching the switch to the load
The resistance arithmetic is the same as for the ADG1411 and worth repeating because it is where most selection mistakes happen. Into a 10 kohm load, 1.5 ohm is 0.015 percent and nothing else matters. Into 600 ohm it is 0.25 percent. Into 50 ohm it is 3 percent, and the 0.3 ohm of flatness becomes 0.6 percent of the swing, which is distortion. In a sample and hold circuit the switch resistance works with the hold capacitor to set the acquisition time constant: 1.5 ohm into 1 nF is 1.5 ns, so the resistance is negligible, but the off capacitance of 23 pF and the on capacitance of 116 pF of a neighbouring channel are what limit the droop and the feedthrough.
Where the part fits
The applications are the same list as its sibling: automated test equipment, data acquisition, battery powered instruments, sample and hold, audio and video routing, communications and relay replacement. The choice between the two polarity versions is made by what the board does at power-up and reset, not by anything in the signal path. Where break before make is needed for multiplexing, the ADG1413 has mixed logic and the make before break protection built in, which is a different requirement from polarity.
For a build that needs the non inverted part, the ADG1411 shares this footprint and this specification table. The pin to pin cross reference page covers how to compare the two without being caught by the polarity change, the how to verify a drop in replacement page sets out the tests to run, and the incoming inspection plan page covers what to check on receipt for switch parts.