Contact Us

ADG1411YRUZ

Brand: Analog Devices
Analog Devices ADG1411YRUZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1411YRUZ — Analog & Mixed-Signal ICs | Superb Automation

ADG1411YRUZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1411YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG1411YRUZ: Four 1.5 Ohm Switches That Turn On With a Logic Zero

The ADG1411 is a quad single pole single throw switch built on an industrial CMOS process that combines high voltage devices with low on resistance: 1.5 ohm typical, 0.3 ohm of flatness across the signal range and 0.1 ohm of match between channels. Continuous current per channel is 250 mA in the 4 mm by 4 mm LFCSP and 190 mA in the 16-lead TSSOP, and this order code is the TSSOP. The part is fully specified at plus 12 V, at plus and minus 15 V and at plus and minus 5 V, needs no separate logic supply, accepts 3 V logic levels on its control pins and is qualified to AEC-Q100 for automotive use.

The polarity of the control pin is the selection criterion

The three parts in this family are the same silicon with different control logic. The ADG1411 turns a switch on with a logic zero on its control input, the ADG1412 turns it on with a logic one, and the ADG1413 mixes the two: two switches behave like the ADG1411 and two are inverted, with break before make action for multiplexer use. That difference decides how a board behaves at power-up and at reset, when the control pins may float or be driven low by a processor that is still booting. A board that expects switches to be off during reset needs the part whose off state corresponds to the level the pins actually sit at, and choosing by part number without checking the truth table is how a signal path ends up connected when the system believes it is isolated.

Why 1.5 ohm matters more than it looks

A switch in series with a signal is a resistor, and its effect depends entirely on what it feeds. Into a 10 kohm load, 1.5 ohm is 0.015 percent of gain error and irrelevant. Into a 50 ohm load it is 3 percent of gain error, and the 0.3 ohm of flatness alone becomes 0.6 percent of the signal swing, which is a distortion term rather than a gain term. Into a 600 ohm telephone circuit it is 0.25 percent. The 0.1 ohm of channel to channel match is what keeps a differential pair balanced, since a mismatch of that size across two 1 kohm legs is 0.01 percent of common mode conversion. These are the numbers an engineer should compute for the actual load rather than reading the on resistance as a single figure.

ParameterValueWhat it decides
ConfigurationFour independent single pole single throw switchesAny combination can be closed at once
On resistance1.5 ohm typical3 percent gain error into a 50 ohm load
Flatness0.3 ohm0.6 percent distortion term into 50 ohm
Match between channels0.1 ohmKeeps a differential pair balanced
Continuous current250 mA in LFCSP, 190 mA in TSSOPThe TSSOP body carries less current
Supply conditionsSpecified at 12 V, at plus or minus 15 V and at plus or minus 5 VThree defined operating points, not a continuum
Logic supplyNone required, 3 V compatible inputsOne less rail on the board
Control polarityLogic zero closes the switchThe inverted sibling is the ADG1412
Signal rangeRail to railSignal can swing to both supplies
QualificationAEC-Q100 automotiveUsable in vehicle electronics
Package16-lead TSSOP and 4 mm by 4 mm LFCSPTwo bodies, different current rating

The supply set is part of the specification

A switch specified at three supply conditions is not specified at everything in between, and the on resistance quoted for plus and minus 15 V is not the number that applies at plus and minus 5 V. The reason is physical: the switch is a MOS device whose gate drive comes from the supplies, so lower rails mean less gate voltage and higher resistance. A product that runs this part at plus and minus 8 V, a common choice for audio, is between two specified conditions and has to characterise its own on resistance or move to a part specified at that rail. The absence of a separate logic supply removes one rail, but the analogue rails still have to be chosen from the specified set.

Where the part fits

Automated test equipment, data acquisition, battery powered systems, sample and hold circuits, audio and video signal routing, communications and relay replacement are the named applications. Relay replacement is the one that has attracted the most movement: a mechanical relay of this current class is larger, slower and wears out, while a solid state switch is none of those things as long as the signal stays inside the rails and the leakage of a few nanoamperes does not disturb the node. Where a signal has to be switched at a level above the supplies, this part cannot do it, because it switches rail to rail and no further.

For a build that needs inverted control polarity in the same footprint, the ADG1412 is the direct answer, and for multiplexing with break before make the ADG1413 is the member with the mixed logic. The ADI part second source page covers alternates for this family, the pin to pin cross reference page lists the fields to compare before a switch is substituted, and the how to reduce component cost page covers the cheaper parts that trade on resistance for price.