Contact Us

ADG1409YRUZ-REEL7

Brand: Analog Devices
Analog Devices ADG1409YRUZ-REEL7 is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1409YRUZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG1409YRUZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1409YRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG1409 four channel differential multiplexer: 4 ohms on resistance and 190 mA of carry current

The ADG1409 switches one of four differential inputs to a common differential output, using two address lines and an enable pin. On resistance is 4 ohms with 0.5 ohm of flatness, the switch carries up to 190 mA continuously, and the digital inputs are 3 V logic compatible with a 2.0 V threshold and a 0.8 V low level. It is built on a process that tolerates 33 V across the rails, so the same part works on plus and minus 16.5 V, on a 12 V single supply, or on plus and minus 5 V.

Published values

ParameterValue
Configurationfour differential channels to one differential output, two address lines plus enable
On resistance4 ohms
On resistance flatness0.5 ohm
Continuous currentup to 190 mA through the switch
Digital input levels3 V logic compatible, VIH 2.0 V, VIL 0.8 V
Supply optionsplus and minus 16.5 V dual, 12 V single, plus and minus 5 V dual, 33 V process limit
Switching actionbreak before make
Signal rangerail to rail, both directions
PackageTSSOP on this order code
Application fitdata acquisition, automatic test equipment, audio and video routing, relay replacement, medical equipment

Four ohms against the load it feeds

Into a 10 kohm load a 4 ohm switch is 0.04 percent of gain error, which is small enough to ignore in a 12-bit system and marginal in a 16-bit one. Into a 1 kohm load it is 0.4 percent, which is 65 least significant bits at 12 bits, and into a 50 ohm load it is 8 percent. The switch resistance only matters when it is a visible fraction of the load, which is why the same part is fine in a multiplexed data acquisition front end and not fine as an audio switch into headphones.

Flatness of 0.5 ohm is the figure that decides distortion. A constant 4 ohms of series resistance only attenuates; a resistance that changes with signal level modulates the signal. Half an ohm across a 10 kohm load is 0.005 percent, which is about 86 dB of distortion, and that is the number that appears when a multiplexer is placed in front of a converter with a 90 dB specification.

190 mA is a carry current, not a signal level

The 190 mA figure describes what the switch can pass continuously without damage, which matters when a multiplexer is used to route a supply or a test current rather than a signal. It is not an indication of the signal range: the switch passes whatever sits inside the rails, and the current limit is a thermal statement about the die and the package.

On a plus and minus 16.5 V supply the total across the part is 33 V, so a signal at plus 15 V and one at minus 15 V can both be switched by the same device. That is wider than most multiplexers and is the reason this family appears in industrial and instrumentation front ends where the input can sit anywhere inside a wide common mode range.

Break before make and what it prevents

The switch opens the old channel before it closes the new one, so two sources are never connected together. In a system where the sources are low impedance outputs, a make before break action would put two outputs in parallel for the duration of the transition, and the resulting current would be limited only by the two output impedances.

The cost of break before make is a short open interval during which the output floats. A high impedance load holds its last value through that interval, while a low impedance load discharges, so the settling time of the channel includes that gap and the source impedance has to recharge the load afterwards.

Two pages worth reading before a purchase order goes out are one stop BOM sourcing and BOM shortage recovery; the first lists what else fits the socket, the second is the test sequence for a drop in, and the power management cross reference covers the case where the shortage is already on the line.

Two questions buyers ask

Does the ADG1409 work with 1.8 V logic? No. The digital inputs need 2.0 V to be recognised as a high, so a 1.8 V driver is marginal at best. The family has members with lower thresholds for that case.

Can two ADG1409 devices be cascaded for eight differential channels? Yes, by using the enable pins to select one device at a time and the address lines to select the channel within it. The enable pins must be driven so that only one device is active, otherwise two channels drive the same output node.