ADG1409YRUZ
Product Specifications
ADG1409YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1409YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1409YRUZ: four differential channels to one differential output, 4 ohm, 190 mA
The ADG1409YRUZ is the differential half of the ADG1408/ADG1409 pair: four differential inputs to one differential output, selected by two address lines, on the same 4 ohm switch. It is specified at plus or minus 15 V, +12 V and plus or minus 5 V, carries up to 190 mA continuously and switches with break before make.
Published values
| Parameter | Value |
|---|---|
| Configuration | 4 differential channels to 1 differential output |
| On resistance | 4 ohm typical, 4.7 ohm maximum at 25 C |
| Flatness | 0.5 ohm |
| Continuous current | up to 190 mA |
| Supply | plus or minus 15 V, +12 V or plus or minus 5 V |
| Switching | break before make |
| Package | 16-lead TSSOP or 4 mm x 4 mm LFCSP |
Why a differential multiplexer and not two single ended ones
Two ADG1408 devices can switch four differential pairs using six of their sixteen channels, and on paper that is the cheaper route. In practice each pair is then split across two packages, and the two legs see different on resistance, different capacitance and, on a board with a temperature gradient, different drift. The mismatch appears directly as common mode to differential conversion, and it cannot be trimmed out because it moves with temperature.
The ADG1409 keeps both legs of every pair on one die, so the match is set by the silicon and not by the board. That is the reason to pay for the differential part on a bridge sensor or a differential audio channel.
What 4 ohm costs a differential measurement
Four ohm in series with a 1 kohm source is 0.4 percent and appears on both legs, so the differential gain error is 0.4 percent while the common mode rejection is unaffected. The error that does not cancel is the channel to channel mismatch, which is a fraction of the 0.5 ohm flatness figure.
At 190 mA the switch drops 0.89 V and dissipates 169 mW. On a differential pair carrying current that dissipation is split over two switches, which is easier on the package than the single ended case, but it still means the pair trace has to be sized for the current and not only for the signal.
Address decoding and settling
Two address lines select one of four pairs, so a channel change is a single decoder edge that switches both legs at the same instant. The injected charge from each leg is nearly equal and largely cancels as common mode, which is why the settling after a channel change is faster than the sum of two independent switches would suggest.
The analog range is the full rail to rail span on a dual supply. On a single +12 V supply the differential pair cannot go below 0 V, so a bridge sensor that sits at a common mode near mid rail needs the dual supply to keep both legs inside the range through the full swing.
Where it fits
Bridge and strain gauge front ends, differential audio routing, automatic test equipment and any four way differential selection where the pair has to stay matched. For eight single ended channels on the same board, the ADG1408 shares the package and the footprint.
Where a customer needs a second position on this part, the ADC and DAC cross reference is the starting point, medical device components sets out the checks a substitution has to pass, and defense grade components is the short lead time route we quote against.
Two questions buyers ask
Can the ADG1408 replace the ADG1409? No. The pin function differs: the ADG1409 switches two legs per channel and needs two address lines, the ADG1408 switches single ended channels with three. The switch inside is the same, the wiring around it is not.
Is the differential pair break before make? Yes, the family publishes break before make switching, so the two legs never connect the two sources during a channel change. That is what keeps a bridge excitation path from seeing a short between channels.