ADG1408YRUZ
Product Specifications
ADG1408YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1408YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1408YRUZ: the 8 to 1 multiplexer in a 16-lead TSSOP, same 4 ohm switch
The ADG1408YRUZ carries the same ADG1408 die as the LFCSP order code in a 16-lead TSSOP: eight single ended channels to one output, 4 ohm typical on resistance, 0.5 ohm flatness, up to 190 mA continuous current, break before make switching, and full specification at plus or minus 15 V, +12 V and plus or minus 5 V. The difference is the footprint, the thermal path and the fact that every joint can be seen.
Published values
| Parameter | Value |
|---|---|
| Configuration | 8 single ended channels to 1 output |
| On resistance | 4 ohm typical, 4.7 ohm maximum at 25 C |
| Flatness | 0.5 ohm |
| Continuous current | up to 190 mA |
| Supply | plus or minus 15 V, +12 V or plus or minus 5 V |
| Package | 16-lead TSSOP |
| Logic | 3 V compatible, no VL supply required |
Choosing between the two packages
The TSSOP is the right choice when the board is built in low volume, when the assembly house inspects joints visually, or when a prototype may need a switch changed by hand. It costs board area and adds lead inductance, which on a 33 V analog node is a small penalty but not zero.
The LFCSP is the right choice when the board is dense or when the switch carries its 190 mA continuously and the exposed pad is needed as a thermal path. On a signal level channel that carries microamps, the thermal argument disappears and the package decision falls back to area and inspection.
The address and enable lines
Three address lines select one of eight channels and the enable line turns the whole device off. On a shared bus the enable line is the isolation element during power down, and it needs a pull resistor so that a microcontroller in reset does not leave the multiplexer connected. The address lines are static during a conversion, which means they can be driven from a port expander or a latch instead of three dedicated pins.
Signal integrity across eight channels
Eight channels in one package means eight sets of analog pins on a 16-lead body. The channel that is off presents its off capacitance to the common node, so seven off channels load the selected path. At a few picofarads per channel that is a load the amplifier must be stable into, and it is the effect that catches a first prototype where the amplifier was chosen for a single channel load.
Keep the common output trace short and do not run the address lines between analog pins. The switching transient couples into the analog path most efficiently through the package pins that sit between the control pins, and a TSSOP makes that coupling visual: the pins that are next to each other are the ones that talk.
Where it fits
Scanning front ends, relay replacement, audio and video routing and battery powered instruments. Because the part is specified across plus or minus 5 V to plus or minus 15 V, one order code can serve a whole product family that runs from different rails.
Buyers usually arrive at vendor consolidation to find the family alternatives, then use BOM shortage recovery to confirm a substitute before it is fitted; how to verify a drop in replacement is the routine for a part that has already stopped shipping.
Two questions buyers ask
Can the TSSOP and the LFCSP order codes be mixed on one product? Electrically yes, mechanically no. They need two footprints and two stencil apertures, so mixing them costs more in assembly than the price difference between the packages.
Does the enable pin have to be driven? It has to be at a defined level. A floating enable can leave the device in either state, and on a shared bus that is an intermittent connection between two boards that is almost impossible to find later.