Contact Us

ADG1408YCPZ-REEL7

Brand: Analog Devices
Analog Devices ADG1408YCPZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1408YCPZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG1408YCPZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1408YCPZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG1408YCPZ-REEL7: An 8 to 1 Multiplexer Rated 4.7 Ohm at 25 C, Not Over Temperature

The ADG1408 switches one of eight single-ended inputs to a common output through three address lines, A0, A1 and A2, with an enable pin that opens all channels. The vendor headline is 4 ohm on resistance, and the table qualifies it: 4.7 ohm maximum at 25 C. That qualifier is the first thing to read, because a multiplexer in an outdoor enclosure does not stay at 25 C.

Where the 4.7 ohm goes

At the 190 mA continuous current rating the switch drops 0.893 V and dissipates 0.170 W. In front of an ADC sampling a bridge, the same resistance is a gain error that moves with temperature and with the channel selected, and flatness of 0.5 ohm is what sets the channel-to-channel mismatch: 0.005 percent against a 10 kohm load, 0.5 percent against a 100 ohm load. The part is built for high impedance sources, and the arithmetic says so.

The published table, as the vendor states it

ParameterValue
Configuration8 to 1 single ended, 3-bit address plus EN
On resistance4.7 ohm maximum at 25 C
On resistance flatness0.5 ohm
Continuous currentup to 190 mA
Supplies specifiedplus or minus 15 V, +12 V, plus or minus 5 V
Signal rangerail to rail, 30 V span on dual 15 V rails
Logic thresholdVIH 2.0 V, VIL 0.8 V
Switching actionbreak before make
Packages16-lead TSSOP, 4 mm by 4 mm LFCSP

The extended temperature version is a different order code

The vendor also lists an ADG1408-EP for defense and aerospace use: minus 55 C to plus 125 C, a controlled baseline, one assembly and test site, one fabrication site, enhanced product change notification and qualification data on request, under drawing V62/11612. A program that needs that paper trail cannot substitute the commercial suffix, even though the switch inside is described the same way.

What the enable pin buys in a real rack

With EN low all eight channels open, so a failed card stops loading the shared bus instead of holding one node at a fixed potential. Combined with break-before-make, that makes the part usable as a relay replacement in test equipment where the address lines are driven by a microcontroller that boots into an unknown state.

Buyer questions

Is the 4.7 ohm figure valid over the full temperature range? The vendor states it as a maximum at 25 C. Plan the error budget with margin above 25 C, or take the number from the curve in the datasheet for the temperature the enclosure actually reaches.

Can it multiplex plus or minus 15 V signals with 3 V logic? Yes. The part is specified at plus or minus 15 V, +12 V and plus or minus 5 V, the signal range extends to both rails, and the digital inputs switch at a 2.0 V threshold, so 3 V logic drives it directly.

Category page: Analog and mixed-signal ICs. Drop-in and near-equivalent parts are listed under pin-to-pin cross reference; parts that have left production are handled through obsolete part cross reference.

Request Quote — In Stock, 100% New & Original, Full Warranty