Contact Us

ADG1404YRUZ-REEL7

Brand: Analog Devices
Analog Devices ADG1404YRUZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1404YRUZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

ADG1404YRUZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1404YRUZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

ADG1404YRUZ-REEL7: a 4 to 1 multiplexer at 1.5 ohms, where 400 mA through the switch is 288 mW inside the package

What the part is

The ADG1404YRUZ-REEL7 is a four channel analog multiplexer from Analog Devices in a 14-lead TSSOP. Two address lines and an enable pin select one of four inputs onto a common output. It is built on the vendor's high voltage CMOS process and is specified at plus 12 V, plus and minus 15 V and plus and minus 5 V, which makes it a part for signal routing and for switching a load, not only for data acquisition.

On resistance is 1.5 ohms typical and 1.8 ohms maximum, flatness is 0.3 ohms and channel to channel matching is 0.1 ohms. Continuous current is up to 400 mA. The part needs no logic supply, accepts 3 V logic levels, and dissipates less than 0.03 microwatts when idle.

Current carrying: the arithmetic that decides the package

Four hundred milliamps through 1.8 ohms drops 0.72 V and dissipates 288 mW in the switch. Through 1.5 ohms it is 240 mW. That heat has to leave a 14-lead TSSOP, and the thermal resistance of that package means the 400 mA figure is a current rating rather than a promise that 400 mA can flow continuously in a hot enclosure. A board that switches a relay coil at 300 mA should compute the junction rise before it assumes the part is comfortable.

The 1.8 ohms is also 180 ppm against a 10 kilo-ohm load, which is negligible for a voltage signal, and 1.8 ohms against a 50 ohm load is 3.6 percent, which is not. The same part is a fine signal switch and a poor one in a 50 ohm radio frequency path, and knowing which of the two the circuit needs is the first question.

ConfigurationFour to one, single ended
On resistance1.5 ohms typical, 1.8 ohms maximum over temperature 2.6 ohms
Flatness0.3 ohms across the signal range
Matching0.1 ohms between channels
Continuous currentUp to 400 mA
Dissipation at 400 mA288 mW through 1.8 ohms
SupplySpecified at plus 12 V, plus and minus 15 V and plus and minus 5 V
Logic3 V compatible, no separate logic supply
SwitchingBreak before make, low charge injection
Package14-lead TSSOP, also 16-lead 4 mm by 4 mm LFCSP
TemperatureMinus 40 to plus 125 Celsius

Flatness is what keeps a signal clean

On resistance flatness of 0.3 ohms on a 1.5 ohm switch is 20 percent of the on resistance, which sounds large until it is compared with the load. Into 10 kilo-ohms the variation is 30 ppm and invisible. Into 600 ohms it is 500 ppm, which at 16 bits is 33 codes and shows up as distortion on a large signal rather than as an offset. Flatness, not the absolute value, is the specification to read when the switch sits in an audio or a signal path.

The 0.1 ohm matching between channels means a four channel scan has almost no channel to channel gain step, so a system can use one calibration for all four inputs. A switch with 2 ohms of matching would need four calibration constants and a temperature table for each.

Where it is used

  • Relay replacement in test equipment, where a mechanical relay would wear out.
  • Audio and signal routing where 1.5 ohms and 0.3 ohms of flatness are low enough to be inaudible.
  • Switching a load current up to a few hundred milliamps between two sources.
  • Gain range selection in instrumentation where the matching keeps the channels aligned.

The failure we see is a switch used to carry a current that a relay used to carry, without a thermal check, and the symptom is a channel whose resistance rises over the first hour of operation. The second is a supply sequenced after the logic, which lets the control pin drive the switch before its rail exists.

Buying this order code

The YRUZ-REEL7 suffix is the 14-lead TSSOP on a 7-inch reel. Buyers ask whether the 8 channel member of the family can replace two of these, which it can if the channel count fits on one common output, and whether a lower resistance part exists for a current carrying path. Below about 1 ohm the family changes, and so does the price.

Comparable multiplexers are on the pin to pin cross reference, the cost trade between switch families is on how to reduce component cost, and the index is on the analog and mixed signal IC page.

Request Quote — In Stock, 100% New & Original, Full Warranty