ADG1212YRUZ
Product Specifications
ADG1212YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1212YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1212YRUZ: the quad SPST in a 16-lead TSSOP for boards that need a visible joint
The ADG1212YRUZ is the ADG1212 quad SPST in the 16-lead TSSOP. Same die as the LFCSP order code, same 1 pF off capacitance, same sub 1 pC charge injection, same 120 ohm on resistance and 33 V total supply, but with leads that can be inspected and reworked by hand. On a low volume instrument or a first prototype that is usually worth the extra board area.
Published values
| Parameter | Value |
|---|---|
| Configuration | four independent SPST switches, control logic inverted against the ADG1211 |
| Package | 16-lead TSSOP |
| Off capacitance | 1 pF |
| On capacitance | 2.6 pF |
| Charge injection | below 1 pC |
| On resistance | 120 ohm |
| Supply | 33 V total range, plus or minus 15 V or +12 V |
| Logic | 3 V compatible, no VL supply required |
The control polarity is part of the order code
The ADG1211 and the ADG1212 differ only in that the digital control logic is inverted. On a board with four channels and a microcontroller that drives all four from one port, the inverted logic means the firmware writes the complement of the pattern the ADG1211 board uses. That is a line of code on a new build and a silent fault on a substitution, because the board powers up with all four channels in the opposite state.
The ADG1213 exists for the case where one board needs both polarities: it carries two switches with the ADG1211 logic and two with the logic inverted. Using one package instead of two keeps the channel to channel match inside one die.
How a quad SPST is used in practice
Four independent switches are usually a channel selection, a gain range selection or a calibration path. Where two of them form a differential pair, the match between them is what preserves common mode rejection, and the pair is better kept on adjacent pins with a symmetrical copper route so the parasitics match as well.
Where the four are independent single ended channels, the number that matters is the leakage: a switch that is off still leaks, and into a high impedance node that leakage is an offset. The part publishes low leakage on the iCMOS process, but the board leakage from flux residue at a 33 V node can easily be larger, so a 33 V board needs a cleaning step that a 5 V board does not.
Thermal and board notes
The TSSOP has a wider body and a longer thermal path than the LFCSP, which is an advantage on a board that may see a fault current through a switch. Keep the analog pins away from the digital control traces, and do not run a control trace between two analog pins: the coupling is small but it appears as a step at the moment of switching, which is exactly when the acquisition is settling.
The supply pins need local decoupling on both rails, placed within a few millimetres of the package. On a 33 V part the decoupling capacitor also has to be rated for the full rail, a 16 V capacitor on a plus or minus 15 V supply is a field failure waiting for a humid day.
For a board that has to keep running while a reel runs out, how to verify a drop in replacement is where the family alternatives sit, the pin to pin cross reference is the check list before a substitute goes in, and component obsolescence management is how a gap is covered without a new line item.
Two questions buyers ask
What is the difference between the ADG1211 and the ADG1212? The digital control logic is inverted between them. The switch, the package options and the analog specifications are the same.
Can the part be used on a single 5 V supply? Yes, with a 0 V to 5 V analog range. The 120 ohm on resistance figure is published at plus or minus 15 V and at +12 V; on a 5 V rail the resistance is higher and should be taken from the low supply column before the error budget is closed.