ADG1211YRUZ
Product Specifications
ADG1211YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1211YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1211YRUZ: four SPST switches with 1 pF off capacitance and a 33 V supply range
The ADG1211YRUZ is the quad single pole single throw of the ADG1211/ADG1212/ADG1213 family, built on the iCMOS process for channels that carry a wide analog swing. Off capacitance is 1 pF, on capacitance 2.6 pF, charge injection below 1 pC, on resistance 120 ohm, and the part takes a 33 V total supply while accepting 3 V logic without a separate logic rail.
Published values
| Parameter | Value |
|---|---|
| Configuration | four independent SPST switches |
| Off capacitance | 1 pF |
| On capacitance | 2.6 pF |
| Charge injection | below 1 pC |
| On resistance | 120 ohm |
| Supply | 33 V total range, plus or minus 15 V or +12 V |
| Logic | VIH 2.0 V, VIL 0.8 V, no VL supply required |
| Package | 16-lead TSSOP or 3 mm x 3 mm LFCSP |
Why 1 pF is the number that decides the channel count
A switch that is off still loads the node it is connected to. One picofarad at 100 kHz is 1.6 Mohm, and against a 1 Mohm source that is a 38 percent error in the amplitude and a visible phase shift. Against a 10 kohm source the same capacitor is a 0.16 percent effect and can be ignored. This is the arithmetic that says how many channels a high impedance sensor can share: the answer is set by the off capacitance of everything hanging on the node, not by the switch resistance.
On capacitance of 2.6 pF is what the source amplifier has to drive when the channel is selected, and it adds to the amplifier's load capacitance. An amplifier specified for 10 pF of load will ring with 2.6 pF plus board and package strays, so the series resistor at the switch input is doing double duty as an isolation resistor for the amplifier.
Logic polarity and the power up state
The ADG1211 and the ADG1212 are the same switch with the digital control logic inverted, and the ADG1213 mixes both polarities in one package. Which order code is fitted therefore decides what the channel does when the control line is high, and, if the control line is left floating at power up, the state of the switch is undefined on all three. A pull resistor on every control input is the cheap way to make the power up state known.
Supply rails and signal range
On plus or minus 15 V the analog range is the full rail to rail span, so a plus or minus 10 V signal passes without clipping. On a single +12 V supply the range is 0 V to 12 V and the negative half of a bipolar signal is lost. The 33 V total range is the difference between VDD and VSS, so plus or minus 16.5 V is the maximum and the absolute maximum rating has to be respected on every analog pin.
Where it fits
Sample and hold circuits, audio and video routing in test equipment, and battery powered instruments that need a wide analog range with almost no quiescent current. For a board that only needs a 5 V analog range, the smaller ADG723 family is cheaper and faster; the ADG1211 earns its price on the 33 V range and the picofarad class capacitance.
The pages that answer this most often are the pin to pin cross reference for the family alternatives, how to verify a drop in replacement for the acceptance test, and vendor consolidation for the case where a replacement has to be fitted before the next build.
Two questions buyers ask
Is the ADG1211 the normally open version? The ADG1211 and the ADG1212 differ only in that the digital control logic is inverted. Whichever order code is on the board, the polarity of the control signal decides the state, so a substitution between them inverts the truth table.
Can it switch a signal that goes below ground on a single supply? No. On a single supply the analog range is 0 V to VDD. A signal that swings below ground needs the dual supply configuration and, at the input, a clamp to keep the pin inside the rails during power sequencing.