ADG1209YRUZ
Product Specifications
ADG1209YRUZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The ADG1209YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
ADG1209YRUZ: four differential channels with 1 pC of charge injection and 120 ohm on resistance
The ADG1209YRUZ is the differential member of the ADG1208/ADG1209 pair: four differential inputs to one differential output, selected by two address lines, on the same iCMOS process as the single ended part. Off capacitance is 1 pF, charge injection stays below 1 pC over the full signal range, on resistance is 120 ohm, and the part is specified at plus or minus 15 V and at +12 V on a 33 V total supply.
Published values
| Parameter | Value |
|---|---|
| Configuration | 4 differential channels to 1 differential output |
| Off capacitance | 1 pF |
| Charge injection | below 1 pC over the full signal range |
| On resistance | 120 ohm typical |
| Supply | plus or minus 15 V or +12 V, 33 V total range |
| Logic | 3 V compatible, no VL supply required |
| Power | below 0.03 microwatt |
| Package | 16-lead SOIC |
Two address lines instead of three
A single ended 8 to 1 multiplexer needs three address lines and a decoder that can select one of eight paths. Four differential channels need two address lines and switch two paths at once, so the control word is shorter and, more usefully, the two legs of a pair are switched by the same decoder edge. That removes the skew a pair of single ended multiplexers would introduce between the positive and negative legs, and skew between legs is exactly what turns a common mode voltage into a differential error at the converter.
The 1 pC charge injection figure applies to each leg. Because both legs are switched simultaneously and the injection is nearly equal, the common mode step largely cancels in the differential measurement, leaving the mismatch between the two legs as the residue.
Where 120 ohm hurts a differential front end
120 ohm in series with a 10 kohm source is 1.2 percent, and on a differential pair the same 1.2 percent appears on both legs so the ratio, and therefore the common mode rejection, is preserved. The error that does not cancel is the on resistance mismatch between channels, which is why the part is bought for its flatness rather than its absolute value.
The settling budget after a channel change is the sum of the amplifier settling, the 120 ohm into the external capacitor, and the recovery from the injected charge. With a 1 nF capacitor and a 120 ohm switch the RC is 120 ns, so a 16 bit acquisition needs about 1.4 microseconds before the sample is valid.
Supply and protection
The 33 V total supply range means the analog side can be plus or minus 15 V while the logic side runs at 3.3 V with no level shifting, and the digital inputs are specified at 2.0 V high and 0.8 V low, so a 3 V microcontroller drives them directly. Every analog input must stay inside the rails: the part has clamping diodes to the supplies, and a source that can go beyond the rail needs a series resistor to keep the clamp current within the absolute maximum rating.
Where it fits
Bridge sensor front ends, differential audio routing, automatic test equipment and any acquisition channel that measures a small difference between two large voltages. The pair of legs inside one package is the reason to choose it over two ADG1208 devices on the same board.
Where a customer needs a second position on this part, the ADC and DAC cross reference is the starting point, one stop BOM sourcing sets out the checks a substitution has to pass, and component obsolescence management is the short lead time route we quote against.
Two questions buyers ask
Can the ADG1208 substitute for the ADG1209? No. The ADG1208 switches eight single ended channels and needs three address lines; the ADG1209 switches four differential pairs with two. They share a package and a process but not a pin function, so the replacement needs a board change.
What is the off isolation at 1 MHz? High enough that the part is normally bought for capacitance rather than isolation: 1 pF of off capacitance at 1 MHz is about 160 kohm of reactance, which sets the feedthrough. For a channel that must be truly isolated, the switch has to be followed by a buffer that is also disabled.