Contact Us

ADG1204YRUZ

Brand: Analog Devices
Analog Devices ADG1204YRUZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADG1204YRUZ — Analog & Mixed-Signal ICs | Superb Automation

ADG1204YRUZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADG1204YRUZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADG1204YRUZ: a 4 to 1 multiplexer with 1.5 pF off capacitance and under 1 pC of charge injection

The ADG1204YRUZ is a four channel to one multiplexer on the iCMOS process, built for data acquisition rather than for signal routing convenience. Off source capacitance is 1.5 pF, charge injection is below 1 pC, on resistance is 120 ohm, and the part is fully specified at plus or minus 15 V and at +12 V with a 33 V total supply range. It needs no separate logic supply and its digital inputs accept 3 V logic.

Published values

ParameterValue
Configuration4 to 1 multiplexer, single ended
Off capacitance1.5 pF source
Charge injectionbelow 1 pC
On resistance120 ohm typical, 190 ohm maximum
Supplyplus or minus 15 V or +12 V, 33 V total range
Transition time120 ns typical, 150 ns maximum
Logic3 V compatible, no VL supply required
Powerbelow 0.03 microwatt
Package14-lead TSSOP or 12-lead LFCSP

Charge injection is the specification an ADC feels

Every time the multiplexer changes channel it pushes a small packet of charge into whatever node it is connected to. Into a 1 nF hold capacitor, 1 pC is a 1 mV step. Into a 100 pF capacitor it is 10 mV, which is 82 codes on a 12 bit converter with a 5 V reference, and 1300 codes on a 16 bit part. The step decays through the source impedance, so the settling time after a channel change is set by charge injection divided by the source resistance, not by the switch resistance.

This is why the part is specified at under 1 pC over the full signal range rather than at one point: the injection of a conventional switch moves with the input level, so the error on channel one differs from the error on channel four and shows up as a channel to channel offset after averaging.

What 120 ohm costs at the converter input

An ADC with a switched capacitor input draws a current spike on every conversion. The 120 ohm switch in series with that spike is a settling limit: with a 1 nF external capacitor the time constant is 120 ns, so a 16 bit conversion needs roughly 1.4 microseconds of settling for one part in 65536, plus the amplifier's own settling. A 1 kohm source with the same switch is 1.1 microseconds and dominates the budget.

If the channel has more than about 10 kohm of source impedance the switch resistance stops being the limit and leakage starts: 0.1 nA into 10 kohm is 1 microvolt, which is still below a 16 bit code on a 5 V range, so the part holds up further up the impedance scale than most 4 to 1 multiplexers.

Why the missing logic supply matters

The part needs no VL pin, so a 3.3 V microcontroller can drive the address lines directly while the analog side runs at plus or minus 15 V. That saves a rail and, more importantly, removes the sequencing question that a separate logic supply creates: there is no order in which VL and VDD have to come up, and no state in which the digital input is above its own supply.

Where it fits

Multi channel data acquisition, sample and hold front ends, automatic test equipment, and audio signal routing where the source is a low impedance amplifier. For a battery powered instrument the 33 V supply range means the analog side can run at plus or minus 5 V or plus or minus 15 V from the same order code, which keeps one part number across a product family.

Buyers usually arrive at the ADC and DAC cross reference to find the family alternatives, then use one stop BOM sourcing to confirm a substitute before it is fitted; how to verify a drop in replacement is the routine for a part that has already stopped shipping.

Two questions buyers ask

Is the ADG1204 a drop in for the ADG604? No. Both are 4 to 1 multiplexers in a 14-lead TSSOP, but the ADG1204 has roughly an order of magnitude lower charge injection and a different pin function on the enable line. The substitution needs a truth table and a settling check, not a pin count match.

What is the analog range on a single 12 V supply? 0 V to 12 V. The part is specified at +12 V single supply as well as at plus or minus 15 V, and the on resistance rises as the total supply falls, so the 120 ohm figure should be read from the supply column the board actually uses.