Contact Us

ADA4084-2ARZ

Brand: Analog Devices
Analog Devices ADA4084-2ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

ADA4084-2ARZ — Analog & Mixed-Signal ICs | Superb Automation

ADA4084-2ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The ADA4084-2ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

ADA4084-2ARZ: dual 30 V rail-to-rail amplifier at 0.625 mA per channel

The ADA4084-2ARZ is the two channel member of the ADA4084 family in an 8-lead SOIC_N body. It runs from a single 3 V to 30 V rail, or a plus or minus 1.5 V to plus or minus 15 V split supply, with both the input and the output reaching the rails. That combination is what makes it a front end part rather than a general purpose amplifier: a 4 to 20 mA loop and a 0 to 10 V industrial signal can share the same stage without a charge pump or a rail to rail level shift in front of it.

Published values

ParameterValue
Supply range3 V to 30 V single supply, plus or minus 1.5 V to plus or minus 15 V split
Supply current per amplifier0.625 mA typical at plus or minus 15 V
Gain bandwidth product15.9 MHz typical at a gain of 100
Unity gain crossover9.9 MHz typical
-3 dB closed loop bandwidth13.9 MHz typical at plus or minus 15 V
Offset voltage20 uV typical, 100 uV maximum in the 8-lead SOIC
Offset voltage drift1.75 uV/C maximum over -40 to +125 C
Input bias current250 nA typical, 400 nA maximum over temperature
Voltage noise density3.9 nV per root hertz typical at 1 kHz
Slew rate4.6 V/us typical
Input voltage rangerail to rail, both inputs
Output swingrail to rail, unity gain stable
Long term drift3 uV typical over 10,000 hours
Package8-lead SOIC_N

Where 100 uV goes on a 30 V span

On a 30 V span one 16-bit code is 458 uV, so the 100 uV maximum offset of this package is about a fifth of a code. The same part on a 5 V span is a different story: one code there is 76.3 uV, so the offset alone is 1.3 codes and the 1.75 uV/C drift adds 289 uV over 165 C, which is another 3.8 codes. The lesson is that a 30 V part used at 5 V is a 5 V part with 30 V protection, and the error budget has to be read from the span the signal actually uses.

The SOIC is the grade to order when the offset matters. The same dual in an MSOP or an LFCSP body carries a 200 uV limit in the SOT-23, MSOP and TSSOP columns, and the LFCSP dual sits at 130 uV, so a purchase order that says ADA4084-2 without the package suffix can land on a part with twice the offset.

Bandwidth at the gain that is actually used

The 15.9 MHz figure is a gain of 100 number, so a channel closed at a gain of 100 has 159 kHz of usable bandwidth, and the 9.9 MHz unity gain crossover is the ceiling for a follower. A 4.6 V/us slew rate limits a 10 V peak to peak output to 146 kHz, which arrives before the small signal bandwidth does, so a large amplitude stage is slew limited and a small one is bandwidth limited.

At plus or minus 15 V the part draws 0.625 mA per channel, so a dual is 1.25 mA and 37.5 mW from a 30 V rail. That is the number to put against a 4 to 20 mA loop, where the whole front end has 4 mA to spend including the reference and the converter.

What rail to rail does and does not promise

Rail to rail input is a real advantage on a single supply board, but it comes with the usual crossover behaviour: the input stage changes over near the positive rail and the offset step at that point is not zero. For a dc channel that spends its life near mid rail the crossover never happens. For a channel that sweeps the full span, the crossover point shows up as a small step that has to be measured on a real board rather than read from the table.

The output reaches the rails unloaded, and the 100 uV class offset means a 16-bit converter on the same supply sees the amplifier rather than the converter as the limit only when the span is 30 V. On 5 V the converter wins.

For a board that has to keep running while a reel runs out, the amplifier cross reference is where the family alternatives sit, how to verify a drop in replacement is the check list before a substitute goes in, and the power management cross reference is how a gap is covered without a new line item.

Two questions buyers ask

Is the ADA4084-2ARZ a drop in for an OP213 or an OP285? The pinout of an 8-lead dual is the same, but the supply range and the input stage are not: the ADA4084-2 is rail to rail in and out from 3 V to 30 V, while the older parts need more headroom and do not reach the rails. It is a socket fit and not a specification fit, so the offset and the bias current of the new part have to be checked against the channel.

Can this part run from a single 3.3 V rail? Yes. The minimum supply is 3 V, so a 3.3 V rail is inside the range with 300 mV to spare, and the input and output both reach the rails. The bandwidth at 3.3 V is lower than the plus or minus 15 V figure, so the numbers in the table above are the high voltage ones.