AD9164BBCAZ
Product Specifications
AD9164BBCAZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD9164BBCAZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD9164BBCAZ: mix mode to 7.5 GHz, and the two package bodies on one order code family
The AD9164BBCAZ is a 16-bit RF digital to analog converter with a direct digital synthesizer that reaches a 12 GSPS effective update rate through a quad switch core and a 2x interpolator, and it is the member of the range that states a mix mode band from 1.5 GHz to 7.5 GHz. Buyers comparing it with the 12.6 GSPS family should start from the band plan rather than the update rate, because the two parts answer different questions.
Published values
| Parameter | Value |
|---|---|
| Resolution | 16 bit |
| DAC update rate | up to 12 GSPS effective, 6 GSPS core |
| Baseband band | DC to 2.5 GHz in baseband mode |
| Non return to zero band | DC to 6 GHz |
| Mix mode band | 1.5 GHz to 7.5 GHz |
| Interpolation | 2, 3, 4, 6, 8, 12, 16 and 24, bypassable |
| NCO bank | 32 NCOs of 32 bit with independent phase accumulators |
| JESD204B interface | up to 8 lanes, lane speed and count programmable |
| Output current | 8 mA to 38.76 mA, programmable |
| Serial port | SPI at up to 100 MHz |
| Signal bandwidth for DOCSIS 3.1 | up to 1.791 GHz |
| Package | 165-ball 8 mm x 8 mm or 169-ball 11 mm x 11 mm CSP_BGA |
What mix mode actually does
In mix mode the converter reconstructs carriers in the second and third Nyquist zones, which is why the stated band starts at 1.5 GHz and stops at 7.5 GHz. A 6 GSPS core has a first Nyquist limit at 3 GHz, so a signal at 7.5 GHz sits in the third zone and the analogue output network has to pass it while rejecting the images below.
The practical consequence is that the reconstruction filter is a band pass component, not a low pass one, and its transition band is set by how far the nearest image sits from the carrier. That is a filter cost that does not appear in the converter comparison table but does appear in the bill of materials.
The DOCSIS 3.1 numbers
1.791 GHz of signal bandwidth is the full cable spectrum, and reproducing it needs at least 3.582 GSPS by Nyquist, which is why the part is specified at 6 GSPS core rate rather than at the 2.5 GSPS that an earlier generation used. A cable head end that puts the whole spectrum in one converter removes a combining network and its losses, and that is the reason this part exists.
For that application the relevant linearity is not the two tone figure at a single frequency but the spurious performance across 1.791 GHz with hundreds of carriers present, and the datasheet's dynamic range claims are stated against the cable compliance rather than against a single tone.
Output current, termination and the 8 mA to 38.76 mA range
The output is a current steering pair programmable from 8 mA to 38.76 mA. A higher current gives better noise at the cost of power and of the voltage swing into the load, and the load is usually a transformer or a differential amplifier rather than a resistor to ground.
At the top of the range 38.76 mA into a 25 ohm differential load is 0.97 V peak, and into 50 ohm it is 1.94 V peak, which is beyond what most 3.3 V amplifiers will take without distortion. The current setting is therefore chosen against the amplifier's input range, and the datasheet's recommended interface circuits are the place to start rather than a bench experiment.
Two bodies, one order code family
The device is offered in a 165-ball 8 mm x 8 mm body with a 0.5 mm pitch and a 169-ball 11 mm x 11 mm body with a 0.8 mm pitch, the latter also available with a leaded ball option for boards that need a compliant joint under thermal cycling. The ordering guide carries three order codes for the family, so the body has to be read from that guide rather than inferred from a distributor description.
The 0.5 mm pitch body needs a finer via and trace rule than a standard high volume process offers, and the 0.8 mm body costs board area but relaxes the escape routing. For a first article the larger body is the lower risk, and the choice should be made before the stack up is released, not after.
Buyers usually arrive at the ADC and DAC cross reference to find the family alternatives, then use the ADI second source page to confirm a substitute before it is fitted; component lead time solutions is the routine for a part that has already stopped shipping.
Two questions buyers ask
Does the AD9164 reach 12 GSPS directly? The DAC core runs at up to 6 GSPS and the quad switch architecture with the 2x interpolator gives an effective 12 GSPS update rate in the modes that use it. The direct RF synthesis band quoted for 6 GSPS operation is DC to 6 GHz in non return to zero mode.
Which package does the BBCAZ suffix indicate? The family is offered in a 165-ball 8 mm x 8 mm and a 169-ball 11 mm x 11 mm CSP_BGA, and the ordering guide carries several codes across the two. Confirm the body from that guide before a footprint is committed, since the pitch difference changes the escape routing.