Contact Us

AD8674ARZ

Brand: Analog Devices
Analog Devices AD8674ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8674ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8674ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8674ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8674ARZ: quad precision low noise amplifier in a 14-lead SOIC

The AD8674ARZ is the four channel member of the AD8671/AD8672/AD8674 family in a 14-lead SOIC_N body. Four channels of 2.8 nV/root Hz, 10 MHz and 75 uV offset at 3 mA each, which is a 12 mA supply budget for a four channel low noise front end in one package.

Published values

ParameterValue
Offset voltage20 uV typical, 75 uV maximum
Input bias current3 nA typical, 12 nA maximum
Supply current per amplifier3 mA typical, 3.5 mA maximum
Gain bandwidth10 MHz
Slew rate4 V/us
Voltage noise density2.8 nV/root Hz typical at 1 kHz
Open loop gain1000 V/mV minimum into 2 k
CMRR100 dB minimum at +-5 V
Output swing into 2 k+3.8 V minimum on a +-5 V supply, +13.2 V minimum on +-15 V
Supply range+-4 V to +-18 V
Package14-lead SOIC_N, also in TSSOP

Twelve milliamps in one package

Four channels at 3.5 mA maximum are 14 mA, which on plus or minus 15 V is 420 mW in a 14-lead SOIC. The package thermal resistance of about 105 C/W puts the junction 44 C above the board, so an enclosure at 70 C would run the die at 114 C, close to the 125 C limit. That is the real constraint on a quad: not the electrical limits but the heat of four channels in one body.

On plus or minus 5 V the same four channels dissipate 140 mW and the rise is 15 C, which is comfortable. The supply voltage, not the channel count, decides whether a quad is a thermal problem, and a 15 V four channel board should either spread the channels over two packages or provide copper under the body.

Noise in a four channel system

2.8 nV/root Hz per channel across a 100 kHz band is 0.89 uV rms, which is 12 codes of a 16-bit converter on 5 V. Four channels do not add in a way that matters, because each one drives its own converter; what adds is the supply current and therefore the voltage drop in the shared ground return. A common impedance of 10 mOhm at 14 mA is 0.14 mV, which is 1.8 codes, so the ground return is worth more attention than the noise figure on a quad board.

The bias current of 12 nA maximum is a bigger term than on a single: four channels each pulling 12 nA from a shared reference buffer will load it, and a reference that was chosen for one channel may not hold its output with four. Check the reference load current, not just the amplifier noise.

When a quad is the wrong answer

Four channels on one die share a thermal path, a ground return and a supply pin, so one channel driving a cable can couple into the other three through the supply. Where the channels are similar and quiet, the quad is compact and cheap. Where one channel is a power driver and another is a microvolt level sensor, they belong in different packages.

For a four channel board that has to be repaired in the field, a 14-lead SOIC is also harder to rework than four 8-lead packages, and a single failed channel condemns all four. That is an argument for two duals on a product with a long service life.

Buyers usually arrive at one stop BOM sourcing to find the family alternatives, then use the amplifier cross reference to confirm a substitute before it is fitted; vendor consolidation is the routine for a part that has already stopped shipping.

Two questions buyers ask

Is 420 mW inside the 14-lead SOIC rating? At 105 C/W it is a 44 C rise, so the junction is 44 C above the board. On a 70 C board that is 114 C, inside the 125 C limit but with little margin, and on a 85 C board it is outside.

Are the four channels independent? Electrically yes, one amplifier each. They share the supply pins, the ground return and the die temperature, which is what couples them in practice.