AD8672ARZ
Product Specifications
AD8672ARZ
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8672ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
Request Quote — In Stock, 100% New & Original, Full Warranty
AD8672ARZ: dual precision low noise amplifier for matched channels
The AD8672ARZ is the two channel member of the AD8671/AD8672/AD8674 family in an 8-lead SOIC_N body. Two channels of 2.8 nV/root Hz, 10 MHz, 75 uV offset and 3 mA each, on plus or minus 5 V to plus or minus 15 V, in one package that keeps a differential pair at the same temperature.
Published values
| Parameter | Value |
|---|---|
| Offset voltage | 20 uV typical, 75 uV maximum |
| Input bias current | 3 nA typical, 12 nA maximum |
| Supply current per amplifier | 3 mA typical, 3.5 mA maximum |
| Gain bandwidth | 10 MHz |
| Slew rate | 4 V/us |
| Settling time to 0.1 percent | 1.4 us on a 4 V step |
| Voltage noise density | 2.8 nV/root Hz typical at 1 kHz |
| Noise, 0.1 Hz to 10 Hz | 77 nV p-p |
| Open loop gain | 1000 V/mV minimum into 2 k |
| CMRR | 100 dB minimum at +-5 V |
| Output swing into 2 k | +3.8 V minimum on a +-5 V supply |
| Supply range | +-4 V to +-18 V |
| Package | 8-lead SOIC_N, also in MSOP |
Two channels, one temperature
A difference stage built from one dual keeps both halves on the same die, so the two 75 uV offsets sit at the same temperature and drift together. On a board with a regulator nearby, two separate single amplifiers can be several degrees apart, and with a bipolar input the offset moves with temperature in a way that a common die largely cancels. That is why a dual low noise part is the normal choice for a differential front end even when board area is not a concern.
The two channels also share supply and ground pins, so 6 mA flows through one bond wire pair. That is a reason to keep the ground return short and to decouple at the package rather than at the far end of the board, particularly when one channel drives a low impedance load.
What 6 mA buys
Two channels at 3 mA are 6 mA, which is 52.6 mAh over a year and a mains or loop powered budget. Against the AD8628 family at 1 mA per channel it is six times the current for 8 times less noise and 15 times less offset drift. The choice is between a battery instrument and a mains instrument, and this part is for the second.
The 10 MHz gain bandwidth at a gain of 100 leaves 100 kHz, which covers audio and most transducer work. A 4 V/us slew rate limits a 10 V peak to peak output to 64 kHz of full power bandwidth, so a large signal at 100 kHz is slew limited even though the small signal bandwidth says otherwise. Both numbers have to be checked against the amplitude the channel actually delivers.
Reading the offset and the headroom together
75 uV is one code of a 16-bit converter on a 5 V span, and the part is therefore a genuine 16-bit front end at room temperature. The open loop gain of 1000 V/mV minimum into 2 k is what keeps it there under load: 120 dB of gain at a closed loop gain of 10 leaves 1 part in 10,000 of gain error, so the feedback network rather than the amplifier sets the scale.
Output swing into 2 k is 3.8 V on a plus or minus 5 V supply, so the usable span is 7.6 V and a plus or minus 5 V converter with a 5 V reference loses the top and bottom of its range. Use a 4.096 V reference or a plus or minus 15 V supply depending on the signal, and size the feedback network for the 2 k load that the swing figure assumes.
Sourcing notes for this family: the ADC and DAC cross reference holds the cross references, how to verify a drop in replacement is the pre substitution check, and OEM procurement is what we use when the part on the drawing is not on the shelf.
Two questions buyers ask
Can the two channels be used as a differential pair for a converter? Yes, and it is a common use: one channel inverts and one does not, both on the same die, driving the two inputs of a differential converter. The resistor matching, not the amplifier, then sets the common mode rejection.
Does it run from a single 5 V supply? The family is specified on plus or minus 5 V and plus or minus 15 V dual supplies, with a supply range of plus or minus 4 V to plus or minus 18 V. A single 5 V rail is not the intended operating point.