Contact Us

AD8656ARZ

Brand: Analog Devices
Analog Devices AD8656ARZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8656ARZ — Analog & Mixed-Signal ICs | Superb Automation

AD8656ARZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8656ARZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8656ARZ: dual 28 MHz low noise precision CMOS amplifier

The AD8656ARZ is the two channel member of the AD8655/AD8656 family in an 8-lead SOIC_N body. It combines a 250 uV maximum offset with 2.7 nV/root Hz of noise at 10 kHz and 28 MHz of gain bandwidth on 4.5 mA per amplifier, which is the combination a 16-bit converter driver needs and most rail-to-rail parts do not have.

Published values

ParameterValue
Offset voltage50 uV typical, 250 uV maximum over the common mode range
Offset voltage drift0.4 uV/C typical, 2.3 uV/C maximum
Input bias current1 pA typical, 10 pA maximum
Supply current per amplifier3.7 mA typical, 4.5 mA maximum
Gain bandwidth28 MHz at 5 V, 27 MHz at 2.7 V
Slew rate11 V/us at 5 V, 8.5 V/us at 2.7 V
Settling time to 0.1 percent370 ns on a 2 V step at unity gain
Voltage noise density4 nV/root Hz at 1 kHz, 2.7 nV/root Hz at 10 kHz
CMRR85 dB minimum at 5 V
Output swing at 1 mA4.97 V minimum high, 8 mV typical low
Phase margin69 degrees at 5 V, 54 degrees at 2.7 V
Supply range2.7 V to 5.5 V single supply

250 uV against 16 bits

One code of a 16-bit converter on a 5 V span is 76 uV, so a 250 uV offset is 3.3 codes and the 2.3 uV/C drift over 165 C adds 380 uV, five more codes. Eight codes total is 0.012 percent of full scale, which is a real 16-bit front end rather than a 16-bit converter fed by a 2.5 mV amplifier. The offset is specified over the whole common mode range, which matters because a rail-to-rail input stage that is trimmed at mid rail often degrades at the ends.

The noise supports the same claim: 2.7 nV/root Hz at 10 kHz across a 100 kHz band is 0.85 uV rms, which is 11 codes of a 16-bit converter. Over a 1 MHz band it is 2.7 uV rms, or 35 codes, so the bandwidth of the stage decides whether the converter sees 11 codes of noise or 35.

Why the low noise figure is quoted at 10 kHz

4 nV/root Hz at 1 kHz and 2.7 nV/root Hz at 10 kHz are the same device measured at two frequencies, and the falling number with frequency is the signature of a small 1/f component that has already flattened by 10 kHz. A stage with a 100 Hz bandwidth should use the 4 nV figure, a stage with a 100 kHz bandwidth can use 2.7, and an audio stage in the 20 Hz to 20 kHz band sits between the two.

The current noise is not in the table because it is small enough not to matter at ordinary source impedances. A 10 kOhm source at 300 K produces 12.9 nV/root Hz of thermal noise, which is four times the amplifier voltage noise, so above 10 kOhm of source resistance the resistor, not the amplifier, sets the noise floor.

Current, heat and the choice against the AD8655

4.5 mA maximum per amplifier is 9 mA for a dual, which is 45 mW at 5 V and 78.8 mAh over a year. That is a loop and mains powered part, not a battery one, and the AD8657 at 22 uA is the answer when the current budget is the constraint. The 370 ns settling and the 250 uV offset are what the current buys.

The single channel AD8655 is the same die in a single package and costs less than the dual when only one channel is needed. Specifying a dual and leaving one input grounded costs 4.5 mA for nothing, which on a multi channel board is a real number in the supply budget.

For a board that has to keep running while a reel runs out, the ADC and DAC cross reference is where the family alternatives sit, the amplifier cross reference is the check list before a substitute goes in, and component lead time solutions is how a gap is covered without a new line item.

Two questions buyers ask

Is 250 uV enough for a 16-bit measurement? It is 3.3 codes on a 5 V span, and the drift adds about five more over the full temperature range. If the product needs better than 0.01 percent of full scale, a chopper amplifier is the next step.

What does 28 MHz of bandwidth mean at a gain of 10? About 2.8 MHz of closed loop bandwidth, which is still far more than a 1 MSPS converter needs. The settling time, not the bandwidth, is the number to check.