Contact Us

AD8648ARUZ-REEL

Brand: Analog Devices
Analog Devices AD8648ARUZ-REEL is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8648ARUZ-REEL — Analog & Mixed-Signal ICs | Superb Automation

AD8648ARUZ-REEL

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8648ARUZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD8648ARUZ-REEL: a quad 24 MHz rail to rail amplifier for four channel signal chains

What this order code is

AD8648ARUZ-REEL is the quad member of the AD8646, AD8647 and AD8648 family, CMOS rail to rail input and output amplifiers that run from 2.7 V to 5.5 V. The part gives 24 MHz of gain bandwidth, an 11 V per microsecond slew rate, 8 nV per root hertz of voltage noise, a 2.5 mV maximum input offset and a 1 pA input bias current, with 2 mA maximum supply current per amplifier. The short circuit output current is 120 mA, which is what separates this family from the ordinary 5 mA buffer amplifiers.

The three members are single, dual and quad. Only the dual AD8647 carries the shutdown function, so a board that needs to power down one channel has to use the dual and not the quad. The AD8646 and the AD8648 are qualified for automotive applications. This code is the quad in tape and reel, and the ARUZ letter string is the body and the reel that the line will receive, not a performance grade.

Parameters as published

ItemValue
Amplifier countfour
Supply range2.7 V to 5.5 V single supply
Gain bandwidth24 MHz
Slew rate11 V per microsecond
Voltage noise8 nV per root hertz
Input offset voltage2.5 mV maximum
Input bias current1 pA
Supply current2 mA maximum per amplifier
Short circuit output current120 mA
Input and output rangerail to rail
Phase reversalnone on input overdrive
Shutdownnot on this member, dual AD8647 only
Temperature rangeminus 40 C to plus 125 C

Numbers that decide the application

Four amplifiers at 2 mA each is 8 mA of quiescent current, so the quad is not four times cheaper in power than four singles, it is four times the current of one part with the board area removed. Closed loop bandwidth follows the usual division: 24 MHz gives 2.4 MHz at a gain of 10, 240 kHz at a gain of 100 and 24 kHz at a gain of 1000. The slew rate puts a second ceiling on large signals: 11 V per microsecond with a 10 V peak to peak output gives 350 kHz of full power bandwidth, which is seven times below the 2.4 MHz small signal figure at a gain of 10. A stage that swings 10 V and is asked for 500 kHz will be limited by the slew rate, not by the gain bandwidth.

The offset of 2.5 mV maximum is 32.8 least significant bits of a 16 bit converter on a 5 V full scale, so this is a general purpose amplifier and not a precision front end. The noise is the stronger number: 8 nV per root hertz over a 10 kHz band is 0.8 microvolts RMS, over 100 kHz it is 2.5 microvolts and over 1 MHz it is 8 microvolts. The 1 pA bias current only becomes visible above roughly 1 Gohm of source resistance, where it produces 1 mV, so photodiode and high impedance sensor work is limited by the offset and the noise and not by the bias current.

The 120 mA short circuit current also sets the load the part can drive. Into 100 ohm that is 1.2 V of swing at the current limit, so a 100 ohm load at 2 V peak needs 20 mA and is inside the part, while a 50 ohm load at 2 V peak needs 40 mA and is also inside it but with the output stage running well above its quiescent dissipation. This is why the family is used as an audio line driver and as a cable driver rather than as a pure instrumentation amplifier.

Where it fits and where it does not

It fits four channel filters, integrators, photodiode and high impedance sensor amplifiers, ADC input buffers and audio line drivers, all on one 3.3 V or 5 V rail. It does not fit a per channel shutdown requirement, a 16 bit absolute measurement without calibration, or a supply below 2.7 V. On a 3.3 V rail the input common mode reaches both rails, so a follower that sits at the positive rail still works, which is not true of the older rail to rail output only parts.

Supply and second source questions

The questions that come back on this family are about grade, package and the reel, because the four amplifiers are electrically identical across the family and only the count and the shutdown differ. A line that was built around a dual with shutdown cannot take the quad silently, and a line that needs four channels should not be assembled from four singles if the board area is the constraint. Where the exact code is short, the family cross reference on the amplifier cross reference page lists the members that share the die and the ones that only look similar in a distributor search.

Sourcing notes and next step

We quote this code against a bill of materials and check the four fields that actually decide whether the line runs: the amplifier count, the presence or absence of shutdown, the body, and the packing. The 120 mA drive and the 24 MHz bandwidth are the two figures buyers ask about most often when they are replacing a slower quad, and both are on the vendor page rather than in a distributor description. Send the line items, quantities and required date through the BOM shortage recovery page and we will answer with availability, and where the code is not on the shelf, with a second source that has been checked against the family on the pin to pin cross reference.

Request Quote — In Stock, 100% New & Original, Full Warranty