Contact Us

AD8646ARZ-REEL7

Brand: Analog Devices
Analog Devices AD8646ARZ-REEL7 is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8646ARZ-REEL7 — Analog & Mixed-Signal ICs | Superb Automation

AD8646ARZ-REEL7

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8646ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD8646ARZ-REEL7: 24 MHz and 11 volts per microsecond from 2 mA per amplifier

The AD8646 is the dual member of the AD8646, AD8647 and AD8648 family: rail to rail input and output amplifiers on a 2.7 V to 5.5 V single supply, with 24 MHz of bandwidth, an 11 volt per microsecond slew rate and 8 nV per root hertz of input noise. The order code reads AR for the eight lead SOIC, Z for RoHS and REEL7 for the 750 unit reel. The difference between the three members is small and worth knowing: the AD8646 is the plain dual, the AD8647 adds a shutdown pin, and the AD8648 is the quad. The maximum supply current is 2 mA per amplifier, and the output can source and sink 120 mA on a short circuit, which is what lets the same part drive an audio line as well as a converter input.

What the vendor page states

ParameterValue
Channelstwo, eight lead SOIC
Supply2.7 V to 5.5 V single
Bandwidth24 MHz
Slew rate11 volts per microsecond
Offset voltage2.5 mV maximum
Input noise8 nV per root hertz
Input bias current1 pA
Supply current2 mA maximum per amplifier
Output current120 mA short circuit
Stabilityunity gain stable, no phase reversal
Qualificationautomotive models listed in the ordering guide

24 MHz is the small signal number, 1.75 MHz is the large signal one

The bandwidth figure is measured at small signal, and the slew rate sets a lower ceiling once the output has to move. With an 11 volt per microsecond slew rate the full power bandwidth is 1.75 MHz for a 2 V peak to peak swing and 875 kHz for 4 V peak to peak, and a 1 V step takes 91 nanoseconds. A filter stage running at 1 V rms therefore sees about 1.75 MHz of usable band, not 24 MHz, and a board that assumed the headline figure will show slew induced distortion at the top of the audio band. This is the arithmetic that decides whether the part is a 24 MHz amplifier or a 1.75 MHz one, and the answer depends on the output amplitude, not on the part.

2 mA per amplifier is 11 mW on a 5.5 V rail

Two amplifiers at the 2 mA maximum draw 22 mW on a 5.5 V rail, and 11 mW each. Against a 120 mA output capability that is a wide ratio, which is why the part sits in the class of amplifiers that drive a load rather than only a converter input. For a battery powered instrument the arithmetic goes the other way: 22 mW continuous is a real share of a coin cell budget, and the AD8647 with its shutdown pin exists for exactly that case.

Noise over the usable band

8 nV per root hertz integrated over the 1.75 MHz large signal band is 13.3 microvolts rms. Over the 100 kHz band of a typical sensor channel it is 2.5 microvolts. The offset is 2.5 mV maximum, so the noise never dominates the dc error at low gains, but at a gain of 100 the input referred offset stays at 2.5 mV while the signal shrinks, and the channel needs either a trim or a lower offset part. The vendor positions the family for filters, integrators, photodiode amplifiers and high impedance sensors, all cases where the 1 pA bias and the 24 MHz band matter together.

Where 120 mA of output changes the choice

An amplifier that can deliver 120 mA into a short will drive a 32 ohm headphone load or a low impedance line without a buffer stage. The same capability is a liability on a converter input if the feedback network is wrong, because the part will happily drive the converter's input protection into conduction. The rule is to size the series resistor for the worst case output, not for the nominal signal. The amplifier cross reference lists the shutdown and quad members of the family, the pin to pin cross reference covers the packages that share the eight lead land, and the analog and mixed signal category page holds the rest of the family.

Request Quote — In Stock, 100% New & Original, Full Warranty