Contact Us

AD8646ARMZ

Brand: Analog Devices
Analog Devices AD8646ARMZ is a analog & mixed-signal component designed for Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8646ARMZ — Analog & Mixed-Signal ICs | Superb Automation

AD8646ARMZ

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8646ARMZ from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

Request Quote — In Stock, 100% New & Original, Full Warranty

AD8646ARMZ: dual 24 MHz amplifier in an 8-lead MSOP

The AD8646ARMZ is the two channel member of the AD8646/AD8647/AD8648 rail-to-rail family in an 8-lead MSOP body. It delivers 24 MHz of gain bandwidth, 11 V/us of slew and 8 nV/root Hz of noise on 2 mA per amplifier, with a 120 mA short circuit output that can drive a converter input or a cable.

Published values

ParameterValue
Offset voltage0.6 mV typical, 2.5 mV maximum
Offset voltage drift1.8 uV/C typical, 7.5 uV/C maximum
Input bias current0.3 pA typical, 1 pA maximum
Supply current per amplifier1.5 mA typical, 2.0 mA maximum at 5 V
Gain bandwidth24 MHz
Slew rate11 V/us
Settling time to 0.1 percent0.5 us at 5 V, 0.3 us at 2.7 V
Voltage noise density8 nV/root Hz at 1 kHz
Channel separation-115 dB at 10 kHz
CMRR67 dB minimum at 5 V
Output swing at 1 mA4.98 V minimum high, 8.4 mV typical low at 5 V
Short circuit output current120 mA
Phase margin74 degrees at 5 V, 53 degrees at 2.7 V
Supply range2.7 V to 5.5 V single supply

24 MHz and 0.5 us of settling

A converter that samples at 1 MSPS gives an amplifier 1 us to settle, and this part needs 0.5 us to 0.1 percent, so the driver is inside the budget with a factor of two. At 2 MSPS the budget is 500 ns and the settling alone uses it, which is where a faster amplifier becomes necessary. The 24 MHz gain bandwidth at a gain of 5 gives 4.8 MHz of closed loop bandwidth, plenty for an anti-alias filter in front of a 1 MSPS converter.

The noise matters at the same time: 8 nV/root Hz over a 1 MHz band is 8 uV rms, which is 26 codes of a 16-bit converter on 5 V, so an anti-alias filter that limits the band to 100 kHz cuts that to 2.5 uV rms. The filter is doing the accuracy work and the amplifier is doing the settling work.

Driving loads and cables

120 mA of short circuit current is a protection number, not an operating point, but it does mean the output can drive a 600 ohm load without the swing collapsing. The channel separation of -115 dB at 10 kHz says the two channels do not talk to each other on the die, so one channel can drive a cable while the other stays on a sensitive node.

Short circuit current into a capacitive load is a different question. The 74 degree phase margin at 5 V and 53 degrees at 2.7 V are the numbers that decide stability, and the lower figure at 2.7 V means a 3.3 V board has less margin for a capacitive load than a 5 V board. Series resistance at the output is the usual answer above about 100 pF.

Why the MSOP version

2 mA per amplifier in an 8-lead MSOP is 10 mW at 5 V and the MSOP thermal resistance of about 206 C/W gives a 2 C rise, so the package is not the limit. The MSOP is chosen for area, and the SOIC version for rework and probing. Both are the same die, so a build can move between them without changing the analog chain.

One warning on the family: the shutdown pin belongs to the AD8647 in a 10-lead package, not to this 8-lead part. A board that needs the 10 nA shutdown state has to specify the AD8647, and a substitution to the AD8646 loses that function entirely.

Where a customer needs a second position on this part, the ADC and DAC cross reference is the starting point, how to verify a drop in replacement sets out the checks a substitution has to pass, and component lead time solutions is the short lead time route we quote against.

Two questions buyers ask

Does the AD8646ARMZ have a shutdown pin? No. Shutdown is a feature of the AD8647 in a 10-lead package. The 8-lead AD8646 has no shutdown, so a board that depends on the 10 nA state cannot use it.

What load can it drive at 5 V? 600 ohm with a clean swing and 120 mA into a short as a protection limit. Above roughly 100 pF of capacitive load, add series resistance, because the phase margin falls to 53 degrees at 2.7 V.