AD8642ARZ-REEL7
Product Specifications
AD8642ARZ-REEL7
Analog Devices — Analog & Mixed-Signal ICs
Product Overview
The AD8642ARZ-REEL7 from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.
Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.
Key Features
- High-resolution data conversion with excellent SNR and THD
- Wide dynamic range and high linearity across operating conditions
- Integrated voltage reference with low temperature drift
- Flexible digital interface — SPI, I2C, or parallel options
- Industrial/automotive temperature range with guaranteed specs
- Low power consumption with power-down modes
Key Specifications
| Resolution | bits |
| Channels | — |
| Sample Rate | kSPS |
| Interface | — |
| Supply Voltage | V |
| Operating Temp | °C |
| Package | — |
| INL | LSB |
| SNR | dB |
| THD | dB |
Applications
AD8642ARZ-REEL7: The SOIC Version, Chosen for the Board Rather Than the Silicon
The AD8642ARZ-REEL7 is the 8-lead SOIC member of the AD8642 family: a dual precision JFET input operational amplifier with rail to rail output, 1 pA maximum input bias current, 750 uV maximum offset, 250 uA maximum supply current for the pair, and a supply range of 5 V to 26 V single or plus and minus 2.5 V to plus and minus 13 V. It is unity gain stable, does not reverse phase beyond the common mode range, and drives capacitive loads above 500 pF without a series resistor. The order code reads AR for the SOIC body, REEL7 for the tape and reel quantity and Z for the lead free finish.
Why the same die is ordered in the wider body
The SOIC and the MSOP versions share an electrical table, so the choice is made on the board. A 1.27 mm pitch body is hand solderable, visible under a magnifier and compatible with a prototype assembled with an iron, which matters on a product that is built in tens rather than thousands. It also has a lower thermal resistance, about 120 C per watt against 190 for the MSOP, although at 6.5 mW of dissipation the difference is 0.4 C and is not the reason to choose it. The reason is assembly and rework, and pretending otherwise is how a team ends up with a package decision that nobody can defend.
| Input bias current | 1 pA maximum, 10 mV into 10 Gohm, 1 mV into 1 Gohm |
| Offset voltage | 750 uV maximum, 9.8 LSB of a 16 bit converter on 5 V |
| Supply current | 250 uA maximum for the pair, 2.19 Ah over a year |
| Supply range | 5 V to 26 V single, plus and minus 2.5 V to plus and minus 13 V dual |
| Output | Rail to rail, stable beyond 500 pF of load |
| Offset over temperature | 750 uV maximum, with the drift term added by the grade in use |
| Die rise at 26 V, SOIC | About 0.8 C at 120 C per watt |
| Pitch | 1.27 mm, hand solderable and visible to the eye |
| Temperature range | -40 C to +125 C |
High impedance sources and the numbers that follow
One picoamp into 100 Mohm is 100 uV, into 1 Gohm it is 1 mV, and into 10 Gohm it is 10 mV. The offset of 750 uV therefore stops being the dominant error somewhere around 1 Gohm, which is the range where photodiode and electrometer circuits live. That is the calculation that justifies a JFET input, and it also shows why the same part on a 10 kohm bridge is being chosen for its supply current and not for its input stage: at 10 kohm the bias current error is 10 nV and irrelevant.
The 750 uV offset is 9.8 least significant bits of a 16 bit converter on a 5 V span, so a direct current measurement at 16 bits needs a calibration regardless of which package is used. The drift of the part is what the calibration cannot remove, and it is the number to read from the grade being ordered rather than from the family headline. A product that calibrates at 25 C and runs at 85 C should budget the drift over 60 degrees rather than over the full range.
Phase reversal, capacitive load and the converter interface
A rail to rail output that is stable into 500 pF can drive a sampling converter's input capacitor through the multiplexer without a series resistor, and the no phase reversal guarantee means an overrange at power up does not latch the buffer to the wrong rail. Those two lines are what make the part usable directly in front of a converter, and they are the ones a cross reference table usually omits. A part that is stable into 50 pF needs a resistor that forms a pole with the sampling capacitance, which shifts the settling time of every channel.
The supply range to 26 V is wider than the 5 V that most converter front ends use, which matters in industrial equipment where the analogue rail is plus and minus 12 V or 15 V and the converter is on a separate 5 V rail. One dual can therefore buffer a plus and minus 10 V signal and drive a converter through a divider without a second amplifier stage, which is a saving in offset error as well as in parts.
Two questions buyers ask
Is the SOIC version electrically identical to the MSOP?
Yes, the electrical table is shared and the die is the same. The differences are the land pattern, the thermal resistance and the assembly route, and the bill of materials treats them as separate order codes for those reasons.
Can a 1 pA part be used with a 10 Mohm source at 125 C?
The bias current rises with temperature, so the 25 C typical is not the number to use. Budget the guaranteed maximum at the hot end, where the bias current error can exceed the offset, or reduce the source impedance with a buffer placed closer to the sensor.
Ordering and supply
The AD8642ARZ-REEL7 is the SOIC, tape and reel, lead free code. Cross references fail on the input stage and on the capacitive load rating, because a CMOS part with a similar offset has a different bias current behaviour over temperature and a different stability into a sampling load. The phase reversal guarantee also differs across families and is rarely printed in a distributor description.
We hold and source this family for production quantities and for repair lots. Start from the family page for analog mixed signal ICs, check a proposed alternative against the amplifier cross reference, and when a substitute is being qualified on an existing board the sequence in how to verify a drop in replacement covers the bias current and the stability checks in the order that catches problems first.
Request Quote — In Stock, 100% New & Original, Full Warranty