Contact Us

AD8642ARZ-REEL

Brand: Analog Devices
Analog Devices AD8642ARZ-REEL is a analog & mixed-signal component designed for Precision Instrumentation and related applications. In stock at Superb Automation — request a quote for competitive pricing and fast delivery.
quote now

Product Specifications

AD8642ARZ-REEL — Analog & Mixed-Signal ICs | Superb Automation

AD8642ARZ-REEL

Analog Devices — Analog & Mixed-Signal ICs

Product Overview

The AD8642ARZ-REEL from Analog Devices is a high-performance analog / mixed-signal IC providing precision signal acquisition, conversion, and conditioning. Analog Devices (ADI) is a world leader in high-performance analog, mixed-signal, and DSP ICs for instrumentation, healthcare, automotive, and communications.

Superb Automation partners with leading brands including Qorvo, TI, ADI, XILINX, NVIDIA, Intel, ST, MACOM, Renesas, and Coilcraft to provide complete BOM and supply-chain solutions.

Key Features

  • High-resolution data conversion with excellent SNR and THD
  • Wide dynamic range and high linearity across operating conditions
  • Integrated voltage reference with low temperature drift
  • Flexible digital interface — SPI, I2C, or parallel options
  • Industrial/automotive temperature range with guaranteed specs
  • Low power consumption with power-down modes

Key Specifications

Resolutionbits
Channels—
Sample RatekSPS
Interface—
Supply VoltageV
Operating Temp°C
Package—
INLLSB
SNRdB
THDdB

Applications

Precision Instrumentation Industrial Process Control Medical Imaging & Diagnostics Automotive Sensor Interfaces Communications Infrastructure Test & Measurement

AD8642ARZ-REEL: 1 pA of input bias current, and the source impedance that makes it matter

The AD8642ARZ-REEL is a dual precision JFET input operational amplifier with a rail to rail output, specified for a maximum input bias current of 1 picoamp and a maximum supply current of 250 microamps per amplifier. The code reads AD8642 for the dual, AR for the 8-lead SOIC body, Z for the RoHS finish and REEL for the reel. It runs from 5 V to 26 V single supply or plus and minus 2.5 V to plus and minus 13 V dual, which puts it in the range where a JFET input is still the practical choice.

Input bias current is the parameter that separates this part from a CMOS or a bipolar amplifier, and it only matters in proportion to the impedance it flows through. One picoamp through a 1 GOhm source is 1 mV of offset, and through a 10 MOhm source it is 10 microvolts. Below about 1 MOhm the bias current is irrelevant and the part is being chosen for its supply current or its input range instead.

What the vendor page states

ParameterValue
Input bias current1 pA maximum
Supply current250 uA maximum per amplifier
Offset voltage750 uV maximum
Single supply5 V to 26 V
Dual supplyplus and minus 2.5 V to plus and minus 13 V
Outputrail to rail, stable with more than 500 pF of load capacitance
Stabilityunity gain stable, no phase reversal
Package8-lead MSOP and 8-lead SOIC
Temperature rangeminus 40 C to plus 125 C, extended industrial

Where a picoamp decides the circuit

A photodiode preamplifier with a 1 nanoamp signal current sees 1 pA of bias current as 0.1 percent of the signal, which is inside the tolerance of most optical measurements. The same 1 pA in a pH probe or an ion chamber buffer, where the source current is in the femtoamp range, is the difference between a usable reading and a saturated output. That is the boundary this part sits on: it is a JFET input amplifier, not an electrometer amplifier, and the vendor page describes it as suitable for photodiodes, ATE reference level drivers, battery management and industrial controls rather than for charge measurement.

750 microvolts of offset against a 5 V range

750 microvolts is 0.015 percent of a 5 V range, which is roughly 0.6 of a 12 bit LSB on a 5 V span. For a 16 bit system the offset is 10 LSB and has to be trimmed or calibrated, which is normal for a JFET part: the bias current is the specification that is hard to find, and the offset is the one that is easy to remove in firmware.

Power at the top of the supply range

250 microamps per amplifier at 26 V is 6.5 mW per channel and 13 mW for the dual. That is what makes a 26 V JFET amplifier practical on a multichannel board: eight channels of a bipolar front end sit under 55 mW, which no comparable bipolar input amplifier at that voltage will match. Where the board runs at 5 V the same part is 1.25 mW per channel and the high voltage capability is simply unused headroom.

Capacitive load and the 500 pF figure

Stability with more than 500 pF of load capacitance is unusual for a rail to rail output stage and it is the figure that makes the part usable as a cable driver or as the buffer in front of a switched capacitor load. At 1 kHz a 500 pF load is 318 kOhm of reactance, so the load is not resistive at the frequencies where the loop gain is high, and the phase margin has to be checked at the frequency where the output impedance and the load capacitance meet.

What to confirm before ordering

The source impedance the part will see, because that is what decides whether the 1 pA matters. The supply configuration, because the input range at 5 V single supply is not the same as at plus and minus 13 V. And the package, because the MSOP and the SOIC bodies are separate codes and the offset limit is quoted per body on the datasheet.

The amplifier family is indexed under Analog and mixed-signal ICs, equivalents from other vendors are in the amplifier cross reference, and drop-in alternatives with the same footprint are collected on the pin to pin cross reference page.

Request Quote — In Stock, 100% New & Original, Full Warranty